Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hello,
Tried the 2.0 nRFSniffer hex file today. It does not show up in WireShark like
the Beta 3 version does, "nRF Sniffer COM6". Tried on two devices with the same result...
My application just hit the following fault randomly:
I tracked back in the map file and that is inside the Nordic NRFX library in ipc_trace_handle, so I have no source...
Is it possible to have discontiguous Non-Secure areas in SRAM to be used by the application?
&sram0 {
reg = <0x20000000 DT_SIZE_K(8)>;
};
&sram0_ns {
reg = <0x20002000...
Hi There
Here we have been encountering some problems and would appreciate if you could help.
We are designing the hardware based on the following schematic, please...
Hi!
Just want to ask if anyone have had the same issue as me, when flashing nRF9160 with J-Link V6.50.
In SEGGER Embedded Studio - Build -> Build and run || Target ->...
Hello!
I use a usb secure bootloader with MBR (without SD) for update my application via USB. Also, my application receives new firmware via GSM modem and saves it to an...
I'm using pc-ble-driver to talk to the nRF52840 dev-dongle from a Windows PC. I started with examples\heart_rate_collector\main.c I receive events in a function 'ble_evt_dispatch...
Hi all,
I want to use the nrf51dk to answer and reject phone calls. One button on the kit would be used to accept calls and another to reject or finish them. The audio...
Hi dear team,
I am using the nRF5840 Dongle and pc-ble-driver-py for development, but I encountered a lot of issue while debugging, I thought I used wrong parameter or other...
We have worked through getting AWS MQTT working and have the FOTA job file loading properly. When the HTTP request is made the file begins downloading but fails to download...
Hello, How do I program the NRF52840 module to read and write data with a single UUID, because the mobile application I used earlier was working with the data read and write...
Hi Nordic
I am trying to run the AWS BLE FreeRTOS demo found at:
https://docs.aws.amazon.com/freertos/latest/userguide/ble-demo.html#ble-demo-mqtt
I am using an...
Hi,
I am developing a product with battery power. To preserve the battery life, this product needs to work in low power mode.
My Environment is a nRF52832, SDK15.2 & custom...
Here S332 -ble_ant_app_hrm file is modified using supported board pca10040 (nrf52832).
There is in pca10040.h file,RX pin number & TX pin number predefined.
And we use...
