Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
Hi
I have been developing ok with Segger Tools and nRF52DK. My application works as expected. However now I need to send hex files to a customer who also has the nRF52 DK...
I have a bunch of custom characteristics in a custom service. I have two different modes of operation that I need to handle and the data associated with these custom characteristics...
Combinig a simplified version of the bsp example and the pin_change_int example I noticed that I'm running into an "[NRF_ERROR_INVALID_STATE]" error caused by nrf_drv_gpiote_init...
I'm trying to send a DFU file but i get en error:
2019-08-16T16:11:40.300Z DEBUG Destroying DFU transport. 2019-08-16T16:11:40.300Z ERROR DFU failed with error: When writing...
DIODE_FWD_VOLT_DROP_MILLIVOLTS is normally depending on how the reverse current protection is implemented in hardware. the current value of 270mV is adapted to the used diode...
The coap_client sample is not building for the nrf9160_pca10090 board. I'm using v1.0.0 of the nRF Connect SDK. The commands used from the coap_client directory are:
mkdir...
Dear Nordic experts,
I am trying to profile embedded S/W on a custom board (call it board #1) with a nRF52840 on it. On this board the trace pins TRACECLK and TRACEDATA...
Hi,
I'm currently trying to evaluate the nRF9160 for one of our projects.
One key requirement is the power consumption when using eDRX.
I have tried profiling the...
I noticed that passkey entry for BLE pairing is usually implemented by the device operating system outside the nrf_connect app. Is it possible to do passkey entry inside a...
Hello everyone,
im using ble tamplate example and Softdevice s140 with the nRF52840 DK.
im trying to change the GAP Data. How and where can i do this?
i want to configure...
the duration field in ble_gap_adv_params_t should be set in in 10 ms units, but currently the timeouts are implemented wrong. APP_CFG_NON_CONN_ADV_TIMEOUT is set in seconds...
Hi Andreas,
Thanks for the details shared.
Also please let us know the BLE SIG MESH – SDK Size of nRF52840 and nRF52832-QFAA / nRF52832-QFAB?
Thanks & Regards, ...
Hi Team,
I am doing FCC testing for NRF52832 BLE. As part of firmware code initialization i have following functions
I am using radio tool radio_modulated_tx_carrier_duty_cycle...
Hello,
I'm using nrf52832 for my application which is required to change dynamically shortcuts of RADIO peripheral.
I'm wondering whether the change can take effect after...
