Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hello,
I use NRF52832 and nRF5_SDK_15.2.0 for our custom board.
Also, FreeRTOS(Tickless IDLE is enabled) is used. And, System ON mode is used for sleep mode.
Now,...
Hello,
I am trying to send data from nrf51822 through UART TX to esp8266. I've gone through the app_uart examples and I can recieve data through RX but having difficulty...
Hello,
First, I follow this tutorial --> https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial . It's working well on the...
Development Environment: Segger Embedded Studio 4.16
Debugger: Segger J-Link Lite/ Segger J-Link Pro
Debugging a custom nRF52810 board using SWD interface.
I am experiencing...
hi
i create mesh network using the light switch client/server every things work well!
i have number of client and only one server.
i set the server to subscribe to the...
Hi,
i'm trying to sort out a performance problem I have with Android clients connecting to my nrf52832 using ble_nus service. Notice my problem is not about the absolute...
I am successfully using the ZigBee OTA upgrade example, but the firmware upgrade takes quite long, approximately a half an hour, so it is not an adequate time at the firmware...
Hi,
I'm using nRF52840 with SDK15.0.0 wit code from : https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-services-a-beginners-tutorial
I could make...
Hi there! I'm an engineering student who is just getting started with all the ARM SoC's and BLE environmenment, in order to develop a project for college. The project that...
I try to test Relay performance of BLE mesh, my setup as following:
1 one client loaded light switch client;
2 two server loaded light server with Relay On;
3 one sever...
Hi, I'm looking to use the nRF9160 DK as an IoT Bluetooth Gateway as listed on the nRF9160's product page. Basically, I am tasked with connecting two nRF52840's (both in GATT...
Hi, I am developping a product with battery power. To preserve the battery life, this product needs to work in low power mode. How can configure nRF51 to advert in low power...
Hi,
I'm using the PCA10056 as a JLINK to my custom board. My board is powered by a LiPo battery through VDDH, and I have access to the SWD pins. I'm also using Segger Embedded...
I started from the blinky example for pca10040e (NRF52810) on SDK15.3, added some files and code to get TWI_MNGR working but i get an error which i can't solve
`.nrf_queue...
