This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I just finished reading the O'Reilly book " Getting Started with Bluetooth Low Energy: Tools and Techniques for Low-Power Networking " where the author uses the nRF51822-EK...
I could run the examples like blinky just out of the box
But, I am clueless how to add a bootloader to this example. I just want to add a simple bootloader from Open Bootloader...
Hi,
we are about to enter bluetooth and expand our products with it. however, the approval process still raises some questions. What I have understood so far (please correct...
Hi everybody,
as already mentioned in the title, I guess to have stumbled across an incompatibility between the app_pwm library and the gazelle link layer.
To keep it...
Hello,
I'm using SDK 15.3.0
I added "err_code=sd_ble_gap_adv_data_set(p_data,31,NULL,0);" to the advertising_init(void) function, but I got the following error:
Error...
MCU: nrf52840
SDK: V 15.3.0 with nRF-IEEE-802.15.4-radio-driver
problem:
I tested repeatedly connection with my nrf52840 production (peripheral) with andorid phone...
Hi,
I have downloaded MDK Keil software .so the problem is if i click on + sign in all devices in pack installer it is not expanding and also i am getting like this
if...
Hello All,
Greetings!!!
I am working on nRF51822. I am used custom board. For reference i used nRF52 SDk 8.1.0 in IAR.
Right now i am use gpio pin as an interrupt pin...
I send 25 byte long messages to unicast addresses in a Mesh network. Because of their size messages become segmented. access_model_reliable_publish() is used for sending....
Hello,
I am using a combination of several Nordic devices and hardware. The nRF52832 is used in a sensor to collect light level information. That data is transported over...
Hello,
I wrote a simple program to turn on externally connected LED at Port 1 and Pin 10. But it is not working. See the code -
#include <stdbool.h> #include <stdint...
Is there any documentation about how to configure the SoftDevice clock configuration using the RC as SoftDevice clock source?
My target is the nRF52832 with the S132 Softdevice...
Folks,
We're wondering how the soft device can work with it being provided as a hex file? Usually with things like this you'd get object code to link to, but that doesn...
Hi,
I am currently working on a project for which I use the Secure Serial UART Bootloader from SDK 15.3 (nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040_uart...
