But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
this device has 2 batteries. so I am adding 2 of battery service UUID(0x2A19). but I cannot access the other of UUID via windows API. but nRF connect for mobile can access...
Hello,
I am trying to use the BMD-350 evaluation board to program a standalone BMD-350 module on a custom PCB. I have followed the instructions in the documentation to connect...
Currently, only one ble_peripheral(based on nrf52840) can connect to the gateway (based on nrf52840) .
The other ble_peripheral( based on nrf52832), will bond to the gateway...
Hello,
As our product (nRF52832, SDK14.2) is heading to radio certification, I was playing around with the DTM example but have some open questions.
I've flashed the...
Hello,
ich have a custom board (with nRF52840 chip) which is programmed over SWD. So the Port ist easy accessable. As base software I am using example/radio_test.
I...
Dear All,
We have designed our custom board based on nRF52810 chipset. wehave not used 32.768khz oscilator. it seems in code default configauration is with crystal. so please...
Hi I'm trying to get started with the the nrf52 Dev Kit and the Bluetooth Low Energy tutorial series, I've downloaded the first example "nrf52-ble-tutorial-advertising" from...
Hi,
I m using NRF52840 as a Beacon. i m using SDK15.2 ble_app_beacon.Advertising is works fine. Now i want to change advertising parameter while button pressed. Here is...
I have the eval board pca 10001. After compiling the demo app for nrf51822_xxaa (256k), keil displays "no cortex-m sw device found" when I trying to flash or debug from their...
Hi,
After provisioning a device using PB-GATT there is a 10 second delay after the PB-GATT connection is closed and the first Mesh Proxy Service advertisement is sent. ...
When I call:
zb_set_network_ed_role(ZB_TRANSCEIVER_ALL_CHANNELS_MASK);
to search for a network across all of the possible channels I can't connect. I can only connect...
Hi,
I'm wondering if it's possible to implement Wireless HART protocol using the nRF52?
If yes, can someone point me the right way (open-source libraries, etc)?
Much...
Hello,
Device NRF52 SDK15.3 SD 6.1 BLE_APP_UART
Host: IPAD mini 5th generation IOS 12.2
we are trying to configure BLE_APP_UART to communicate with IOS 12.2 device...
