We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hey all, my QSPI woes continue. I'm trying write 4 bytes (0xDEADBEEF) of data to a flash chip, equivalent to the NRF52840 DK. I'm using PP4IO and 24 bit addressing mode but...
Hello,
I am using the NRF_LOG_INFO macro to print certain event results. I am writing a large chunk of memory over I2C. The operation succeeds but the log print is only...
Hi All,
I' ve successfully programmed an nRF52840 device with an application running with PHY_CODED modulation and I can scan it from my Samsung Galaxy S+. Unfortunately...
Hi, I'm running nRF5 SDK v15.2, and tried to run the led softblink example on port 1 of a nRF52840, which did not seem to work. I found a problem in low_power_pwm.c, which...
We want to use some device in the peripherial mode.
after the devices were bonded, for next connect I need to hide this advertise packet from air in the nRF Connect util...
We have a problem that we thought was isolated (affecting only one phone) until recently we started getting more phones exhibiting the same issue.
We are Australia based...
I can pair and bond as a Zephyr central via bt_conn_auth_register & bt_conn_security().
When the bond is successful I get a callback to cb_pairing_success(struct bt_conn...
Hello,
I am trying to read the internal temperature sensor using interrupts (SoftDevice is disabled). This is what I have:
#include "nrf_temp.h" #include "nrf_nvic.h"...
I am having hard fault when `nrf_sdh_enable_request` is called in BLE init. I am following BLE_TEMPLATE. I did not copy the solution, I am extending TWI example to include...
Hi,
I am trying to make a micro second timer count and I am using the timer driver from the timer example. However the timer init is failing in my code and I am not sure...
Hello,
I am using pc-ble-driver to write a desktop application interfacing with Nordic connectivity dongle. There is no automatic discovery module functionality so I have...
I am trying to just find what is this LE Secure Connection but can't seem to find anything basic. When i look at the lesc example, it look slike they simply turn the bit on...
Hello,
I am having a custom nRF52832-based central device - it works fine when connecting a single nRF52832-based peripheral (the both are based on SDK 14).
Now I need...
(added comment regarding intitialisation of GZP_PARAMS sunday 19 Aug)
I would very much like to use the gzp_dynamic_pairing package on the nRF52. Unfortunately I cannot...
hi, i am doing a project where i have to change adv name of ble device.
i am using nrf sdk 15.3.0 ble_app_blinky example for pca 10040e because it has all the things i need...
