We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
In the NRF52-DK user guide, the following is stated:
Important: When using ANT/ANT+, the 32.768 kHz crystal (X2) is required for correct operation.
However, I could...
I need a help to create a mesh where two nrf52 dk are connectred in the mesh and one node sends a message and another node recives it and sends to a url
Hello,
BLE MESH 3.0 Light Sw Example code just I have add APP_TIMER_MODE_REPEATED and its work fine.
Case 1:if I print string Or LED Toggle Based on timer its working...
Hei there!
First of all thanks for all the great work here!
My question is:
In my application, the final device will have 4 pogo pins.
Two of them are for power, the...
Hello All,
Hello all,
I am working on BT832A in which nRF52810 is used and i used segger studio for programming in windows 7. I am refer nRF52 SDK 15.2.0. And i am load...
In the manual for the nRF5284 there is a listing for some divider settings for the MCKFREQ. The size of the register and the values to set indicates that there are a much...
Hi
working on a NRF51822 device with SDK12
I was using nrfjprog version: 9.7.1 to create a setting.hex with the following line
nrfutil settings generate --family...
i am using this project:
\nRF5_SDK_14.2.0_17b948a\examples\ble_central\ble_app_uart_c\main.c as center.
nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\main...
I implemented the app_pwm_library, but it seems to "top out" at 500Khz? Here is a summary of my code. Is there a set of routines that have a higher speed?
APP_PWM_INSTANCE...
Good morning,
I already made a nRF51822-based prototype some years ago, and now I'm working on a new prototype but based on the nRF52840.
Is there any AN like the nAN36...
The design I am working with has no RTC. Is it possible to use nrf_drv_timer to "wake up" the CPU? I understand I will not be able to use app_timer code, so I was trying to...
Hello,
I am trying to use an interupt from an analog devices ADXL343 accelerometer.
With a power supply of 3.0V to my board, I only get a 2.1V on the interrupt, and I...
Hello! What does the real marking of the nRF24L01 + chip look like? I have not such, but very similar. The problem is that the module after a while ceases to go to sleep,...
