This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello!
I'm having a problem and a hard time trying to understand what's wrong. Currently, I'm using the SDK 14.2.0, SD 5.0.0 and Segger on macOS 10.14.2.
I'm using the...
Hello,
I have a product using NUS profile and plan to update it to support connection from multiple phone
Do you recommend to start from Multiperipheral example and...
if i use this code to send data,i sometimes miss data..
do { err_code = ble_nus_string_send(&m_nus, (uint8_t*)data, &data_len); if (( err_code != NRF_ERROR_INVALID_STATE...
I have nrfutil version 5.0.0. I run this command:
nrfutil pkg generate --hw-version 52 --sd-req 0xA8,0xAF,0xB7 --application-version 2 --application ./nrf5/Debug/nrf5.ihex...
Hello! We are trying to use Nordic AndroidScannerCompatLibrary in our Android application to scan BLE devices and measure its RSSI level. BLE devices is mounted on ceiling...
Hello there,
I would like to read the data I sent through a WS2812b LED string. I drove it using I2S. Upon reading it, seems like it is not a good idea to read it using...
Not sure what I did to cause this, but my nRF52840 no longer works. I searched for solutions and came across:
https://devzone.nordicsemi.com/f/nordic-q-a/24592/my-nrf52...
Hi,
I am wandering if it would be possible at all, to wrap a quarter wave antenna printed on flex pcb around a cylindrical battery (LiFePo4)?
Would the radiation be...
Hello,
Information:
SEGGER Embedded studio Studio v412
Windows 10
nRF52832 on a development board.
We are attempting to merge an application with a bootloader...
I have read that the nrf51822 is not supported anymore in the examples of SDK's older then V12.
Does the nrf51 completly not work anymore with newer SDK's or are only the...
I have my system working with softdevice compiled in but not enabled. System communicates with external chip using SPIM peripheral, everything is working fine until I enable...
Hi,
I have my custom board wired to the nRF52 development board. I am using SDK 15 and softdevice 132 for this. I am trying to set up SAADC to measure adc data on Analog...
Hi,
I'm only seeing the GPS_SIM driver in the nRF Connect SDK. Is there any driver to enable any evaluation of the nrf9160 on chip GPS anywhere?
Regards,
Kilian
