We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hello,
I am having difficulty using a single TWI to support a DAC (MCP4725) and IMU (BNO055).
I am using nRF52 DK, and SDK 14.3 with the SEGGER IDE. The DAC is running...
Hi,
I am trying to run lte_ble_gateway sample on nrf9160 DK, but in debug I can not catch breakpoint on main().
When I going in debug mode step by step I find that the...
Hi
I am new to the NRF52840. I am trying to receive data from nrf24L01+ to the nrf52840 Development kit. I find some examples from the SDK radio receiver using PCAl0056...
Hello all：
I am using nRF52-DK（pca10040）to do some tests.
I want to use gazell and at the same time, I want to detect the events of the NRF_RADIO, connect it to PPI. ...
Hello,
I am using Eclipse to create a project using code from ble_app_hrs and I am developing for a nrf52832 chip. Unfortunately, I am getting a "was not declared in this...
I send a sequence of characteristic writes to my device, in code based on the nRF Toolbox. Sometimes I see this error message. Why does it happen and what steps can I take...
Hi Team
I created an own interface layer using the mesh SDK's "flash_manager" to have a simple API for accessing my application flash area.
Now, I am facing the problem...
Hi there,
I am migrating a project from SDK13 to SDK15.2, where I need to change the advertising data dynamically and change the ble_gap_adv_params_t properties type between...
I am using SDK12 with nrf52832. UART working fine (with FIFO) and Timer1 also works.
I wanted to set a 1 minute timeout around the UART dialog to handle disconnection etc...
Hi, watched your long distance test video. I can find the code in the file NRF5_SDK_15.2.0_9412b96.
How to change the output power (db type example 2 db or 3db)
Hello, I am currently evaluating the nrf52840 and nrf52832 for the purpose of bluetooth mesh. I found flash usage information in the mesh SDK documentation as follows:
Build...
So I'm very new to the Nordic nRF52 and nRF5 SDK. I'm using the blinky examples as a starting point for a remote control that will drive motors. My customer's question is...
As per my requirement, I need strong pairing mechanism, i am referring ble_app_gls example of nRF5_SDK_15.2.0_9412b96 sdk for checking pairing. As i have seen in the code...
Hi,
I could not find any example of the 802.15.4 stack API that talks directly to the PHY Layer, by means of PD-SAP and PLME-SAP, as shown in this picture:
https://github...
Hi,
I am currently using nrfgo mother board ( nrf6700). I could able to connect to nrfgo studio and see it is connected I can also program external device through ISP. Cant...
