Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Above is the trace and the commands inserted. We were unable to get a response using the at+cops? command. Both SIM cards were active that we tested. We tested band 12. Could...
I would like to know more about the TLS 2K packet limitation in the nRF Connect SDK.
Is there a way to not be constrained by this limitation. I've seen some posts about...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I am following the link;
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson...
Hi,
I'm hoping you can help.
I am using the CENTRAL_UART and PERIPHERAL_UART to evaluate the nRF52840, and using a terminal program works fine.
What I want to do is...
Hi all,
I have a problem that seems very simple, but I cannot make sense of it.
I have a simple setup on the NRF52840 DK that senses a rising edge on pin 1.00 and...
I am trying to write tests for my code using CppUtest. I know the platform has memory leaks detection support. it seems that everyting is set up correctly to see the results...
Hello,
I am starting with the nRF Connect. I got a nRF52840 DK and I am following the 'nRF Connect for VS Code' YT series.
I got as far as part 5 (debugging), but I cannot...
Hi all,
SDK: NRF Connect v2.5.0 We've made a custom PCB with the NRF9160, and we have made a custom board configuration for it.
Our issue seems to appear when trying to...
Hello,
I have a mosquitto broker running on my pc. I want to connect and published to this broker through nrf9160.
The issue that I am facing is that prj.conf file only...
I want to use RTT log to output some data, but the data is output. 6 bytes in a line, but the first byte is an independent line, and the next 6 bytes are a line, staggered...
I would like to enable and configure the high power mode on the DC to DC converter in the nRF52840.
I am looking for the device tree source entries and the necessary entries...
Board: nrf7002 Project: matter_light_blub OS: Kubuntu 22 Toolchains: v2.6.1 SDK: v2.6.1
I am developing with the nrf7002, and my current setup involves using a Samsung A54...
Hello,
Is there examples of paring,bonding and whitelisting?
The pairing and bonding mode is static password.
It is best to have examples of the central and the peripheral...
Hi Nodic support team.
I am using esb_ptx and esb_prx for testing interface.
Can i change nrf_esb_payload_t.data in receiver of esb_prx?
It is always 8 bytes even though...
