Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I'm trying to reflash the dongle with the "connectivity firmware". I previously used nRF Connect to do that, but with the latest version, the bootloader got somehow corrupted...
Hello everyone,
I'm currently transitioning a project from traditional BLE communication to the Nordic UART Service (NUS). The previous setup worked fine, but after replacing...
I get error about MPU error stack size while trying to run the example from ncs v2.7.0 on nrf52833dk
I was able to build correctly and I see in the log file that it gets...
nRF Connect SDK 2.3.0 on nRF52840DK
I am trying to add a fifo to my application but when trying to allocate the memory for the data item, k_malloc always returns NULL no...
Hello,
I have custom hardware running on nRF53 and there are multiple sensors connected with it for the measurement of their different entities. The hardware is battery...
Hello Experts,
On my Windows 10 PC, I have installed nRF for Desktop v5.0.2 and J-Link Pack version 7.94e got installed along with it.
Also installed Nordic command...
I use nRF52840DK and nRF21540EK to develop BLE programs, and the program uses FLASH for BLE image storage, the program works well on the DK. However, when I burned it into...
Hello,
I try to flash my bmd-345-eval board with nrf connect visual in VS code.
But the connected devices don't show mcu but show VCOM0 and RTT on nRF connect in VS code...
Hi
I have a issue, I have 4 samples nrf9160 module, all run in same firmware with FOTA feature
I found that only one module cannot start FOTA, then I try to read message...
I am getting the following build error for a Nordic nRF5340dk
c:/ncs/toolchains/ce3b5ff664/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm-zephyr-eabi/12.2.0/../../.....
Hello,
We have an issue regarding PSM availability when roaming. Some operators do not grant PSM and once a device connects to such a network, it would drain the battery...
Hi, When performing GATT discovery on the peer device I observe that the procedure takes too long about 5-6 seconds even at the lowest connection interval. The same process...
I was trying to add the nrf91-modem-trace-uart snippet to my build configuration. I've found that it does not take effect when using the "Add Build Configuration" UI in the...
Hi support team
If I want to implement update advertising data dynamically function, which method is recommended?
1. bt_le_adv_stop (); and bt_le_adv_start (adv, ad, ad_len...
Hello,
I am primarily an STM32 user, delving into Nordic. I will be creating a product using the nRF52832. I would like to measure the 32MHz & 32KHz clock inputs to the...
