Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I would like to read a large data file from SD card and send over BLE from my device to an Android smartphone. I have adapted the ble_app_uart example into my program...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
I am considering adding the following bootloader to my project. nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader...
I'm trying to distinguish disconnect reasons for debugging purposes. I've been able to glean that
BLE_HCI_LOCAL_HOST_TERMINATED_CONNECTION means that my device initiated...
We use a gpio to control the system power. This gpio need to be kept high when system is running. If doing a soft reset, this gpio will be low. System will power off directly...
Hello,
I am having an issue with Zephyr, it constantly reboots the system because of stack overflow.
Sometimes in these faults, it says "Fault during interrupt handling...
I am trying to use RTC to get timestamp (to get current time). So, I am using FreeRTOS which uses RTC1 by default, libuarte which uses RTC2 and I am not using softdevice as...
I am trying to program my Thingy:53 with the Edge Impulse precompiled application firmware which I downloaded from the nordic website. The nrf Programmer Desktop app is showing...
Using NCS 1.7.0 with a an nRf9160/nRF52820 split Host/Controller as a peripheral and an nRF52840 as a central. I can connect to the peripheral with my central fine and write...
hello Nordic
i am working with ncs 1.7.1 (soon we are moving to zephyr 2.9)
i want to add a driver self test functionality for some of my drivers so in my application...
Hello We have been using the RSA example found in the nrf_cc310/rsa which uses INTEG_TEST_PRINT, a mask of SEGGER_RTT_printf, for debugging. When using NRF_LOG instead of...
Hi,
I have a working code that uses the UART FIFO instance which uses the app_uart_put and app_uart_get functions to communicate to an external LCD module. I want to now...
NCS 2.0.0
I start a timer using k_timer_start with a duration of multiple seconds (ive tried 10, 30, and 60) but the immediate next line of code (k_timer_status_sync) never...
Hello,
I'am working on a custom project with an nrf52832. Now I want to use the nrf52 to emulate an nfc tag. Regarding to the technical documentation, the nrf52832 supports...
Hello,
I am working on developing an application on the NRF5340 development kit which scans for nearby BLE beacons. I am using the Bluetooth RPC Stack for communication...
