After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
i2c_recover_bus is used to re-sync slave devices on the i2c bus when they may be out of sync due to a reboot or other event.
i2c_recover_bus is currently not causing the...
Hi,
I'm mid-way through designing a custom board using the nRF52840. As I am space and height constrained I need to use the Tag Connect style connector used on the nRF52840...
We want to be able to manually send Friendship requests from LPN or to change request interval runtime.
It was possible to send requests manually using nRF5 Mesh SDK, however...
Hi guys;
I try to read and write the data without connecting nRF52832 .is there possible to do? Then is it correct or not? if it's wrong means give me the possible solutions...
I have a DK board with nRF52832 that I've been using several months with no problems.
Today I wanted to try an experiment and did some modifications to the startup ASM...
Hi,
Our setup is a new design with SDK 17.1.0 and it is expected to support DFU over BLE. We are using the nRF52832 SoC.
I am trying to understand the role that is being...
Hi,
We are having an issue modifying the blinky_pwm example for our needs. We have made a devicetree overlay file setting the pwms of &pwm_led0 to 28 and pwm0's ch0-pin...
I would like to use nrfjprog to erase nRF52832 device. But it failed with "An unknown error". The nRF52832 device connect to laptop through J-Link USB interface.
D:\Nordic...
Agenda : Use crypto features like AES-CBC, AES-CCM, RSA, ECC, etc. in secure environment (i.e. trustzone with SPM). Also, to use HUK, KMU for secure key generation and storage...
Hi All, I am migrating some applications (each with multiple custom board) from nCS1.5.1 + nCS1.9.1 to nCS2.0.0 I also noticed that in nCS2.0.0 the build output folder is...
Hi,
Depending on how the nRF5 SDK is configured, the BLE address may change once in the bootloader (it's incremented). This happens in the gap_address_change() function...
Hi Everyone,
I am trying to do OTA on NRF52833. In my previous project I was able to do OTA on NRF52840. The memory requirements for the project were as follows:-
Memory...
Hi, I'm trying to configure my VScode project for the nrf5340dk using the nrfconnect sdk to be more version control friendly and require less interactions to set it up. I...
hi..... everyone
I want to send the data from one node to particular node and that same data should want to print in termite using uart . so i checked the ble_uart coexist...
Hi all,
I'm trying to use the nRF52840-DK board to interface with the MAX31865 RTD-to-Digital Converter. I've adapted the MAX31865 C++ library to C and replaced the Arduino...
