Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I want to do firmware updates over BLE. To do that I added these settings to my prj.conf which I mostly got from the smp_svr example:
This "works" but it uses the default...
Dear DevZone,
I would like to add a nrf21540 range extender to my board based on nrf52840 MCU. Our lab is based in Italy and we would need to respect the regulamentation...
Currently, I am following guide of zephyr sample: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/subsys/mgmt/mcumgr/smp_svr/README.html But when...
Hi
we are developing a successor for one of our products based on the nRF9160. One important feature is the debug UART. There are 2 ways to connect to this UART. Either...
Hello,
We have a software running on the nRF52832 which was developed with the nRF5 SDK. It contains a bootloader, S132 softdevice and our custom application.
The bootloader...
Hello,
When looking at the datasheet, we see that the modem power consumption can be really high in high power tx scenarios, 23dBm for example the modem consumes almost...
Hi,
I am looking to perform programming on a nRF52832 on a custom PCB. So far I am planning to use an SWD connection with my nRF52DK to upload my application.
1. I was...
Hi,
I'm looking for some documentation for both projects. While there inline documentation and example projects are existing, I couldn't find any javadoc (or similar,...
Hi,
I want to use two SPI instances (0 and 1) in my project. I am able to modify the example SPI project to use 2 SPI instances as in the code below and setting #define...
I'm trying to get the ADC running on an nrf51DK, however whatever configuration I use it always outputs a value equivalent to ~0.6v input. I've tried with the basic ADC example...
I bought a product with NRF52840 as MCU. Now I want to communicate with other devices over RS485. So I had to make some changes. I have the following questions and hope to...
i try to build simple hello world program in c++. it successfully compile just yesterday, but somehow it fail to compile now. on the log it seem to use /usr/bin/c++ to compile...
The following code snippets produces Error code 0x0005 when trying to update a characteristic value via custom characteristic programming nd connected to nRFConnect app: ...
The nRF52833 datasheet lists a number of pads as "N.C." however I could not find anything in the datasheet about what to do with these pads. Is it safe to route traces over...
hi
I would like to use BLE Mesh to control my products. I would like to build a mesh network in advance, install a provisioner and automatically provision the nodes when...
