Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I am working with NRF52840, I am using segger embedded studio as V5.42a from that I build the example code as ble_app_proximity. I am getting some error as "Output/Debug...
Hello, I am a private developer of wireless gaming mice in Japan. I am thinking of using Nordic's nRF52840 as the MCU, but can this chip be written to only by USB without...
Hi
I added some code to get the PA/LNA driver enabled in the DFU bootloader on my board accordig to this post:
https://devzone.nordicsemi.com/f/nordic-q-a/50687/pa-lna...
Hello! I am quite new to hardware design with these chips, I have been working with NRF24LUP1 for a while, and have custom bin file for it, not a hex file. and I am unable...
Hi,
I am trying to send the data from SAADC on BLE. I follow the example: https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode...
I use PCA10059 demo board,receive BT data by" nrf connect for desktop",yesterday it is ok,but today when I plug it into my PC,it can't be recognized.and no any indicator,...
My peripheral_demo is already able to work. Now I'm trying to add dfu to it.
I followed the instructions here. (+) Add DFU support to your application - Software - nRF Connect...
I have been able to set up external flash for MCUBoot for FOTA.
But after rebooting, the image is the same than before the image upgrade.
I used a sniffer so i could...
Hi,
I have been looking at the sample https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples/samples/nrf9160/simple_at and see that the socket() function uses...
Hi all,
I'm trying something similar to this:
https://devzone.nordicsemi.com/f/nordic-q-a/21628/how-to-use-nrfjprog-dll
i.e. using the nrfprog.dll to connect with a...
Hi,
How do you create a macro in the nRF Connect Mobile app (Android) that displays RSSI in the log every time I receive a temperature signal.
Thanks very much.
Hi,
I have nrf52840 based BMD340 evolution board. I am able to run beacon transmission example.
ble_app_beacon.
Now I want to receive beacons and see the list of it...
I use nrf_fstorage_write() to write data to fstorage. And then I use nrf_fstorage_read() to read data. But data of fstorage written data and reading back are not the same...
Hi,
I have been stuck on this issue for a long time, I have created a buetooth mesh network using NRF52832 IC, which I have completed perfectly.
But the issue is I...
I have seen webinar on YouTube where NordicSemiconductor demonstrated a peripheral_hr that send simulated heart rate data from nrf52833 to nrf android app. But now I want...
