This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
I've been using the nRF5 SDK (17.1.0) USB Mass storage code for a data logger I have made. I am using a memory chip larger than 16KB and that code has bugs when you...
Hello,
I am currently using the nrf52840 evaluation board in developing a prototype. Once this goes into production, what are my options for programming the firmware? What...
When using l2cap to stream data at a high rate from device to an app we are seeing a hard fault in l2cap_data_pull when there is queued l2cap send data.
When the fault...
Hi,
I encountered a stop scanning issue when running the nrf5340_audio application without any configuration changes .
The only modification I made was changing the log...
I am building a firmware based on nRF Desktop, but can reproduce the issue in nRF Desktop SDK 2.9.0. The issue is that MCUBoot takes almost 1s to start the app, even with...
I'm using the visual studio code extension and things work well. I am now trying to test a more complex project found here but when pressing build I get some very long errors...
I am currently working on a distance measurement library using the nRF52840 DK and nRF52840 dongle. I have successfully obtained distance values on the serial terminal, but...
Evaluating direct access I2C operation with the NRF9160DK. I have a INA219 connected to pin 30 & pin 31. I am aware that there is a zephyr driver for the INA219, but I want...
Hello all,
Going through the nRF Connect SDK Intermediate course with my nRF54L15 DK, I stumbled upon a problem at step 6 of exercise 3 - Interfacing with ADC using nrfx...
NCS 2.6.0, sysbuild with mcuboot
nrf52840
I'm trying to add LED indication during mcuboot image transfer. Currently it takes 20-30 seconds for the image copy and the...
Hello, I'm in the development stage of a product and currently evaluating the nRF5340 as our main processor and nRF7002 as a companion IC for WiFi. Our application can be...
Hello, I cannot use UART1, and I don`t know the reason for that. I run the exercise: https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-4-serial...
Hello,
When following Lesson 8: Exercise 2 – DFU over USB, adding external flash & custom keys, SDK v2.6.2, I encountered an issue with step 7.6. Upon issuing the command...
Hello support team,
I have two development kits: one nRF5340 DK and one nRF5340 AUDIO DK .
On the nRF5340 AUDIO DK , I have flashed the unicast server example. Now, I...
