After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
Hello,
I am creating a BLE Rx/Tx connection between two NRF52840-DK's similar to the Nordic UART Service. With the goal to achieve around a 100/100 KB/s connection. Only...
I have a system that consists of a sensor (nRF52840), hub (nRF5340), and gateway (nRF9160). The high level end goal is to be able to publish a MQTT message from the sensor...
Hi,
I'm looking for AES encryption aes_ctr, nrf_crypto example to try on NRF52811 but, I don't see any example for pca10056e.
Does that mean nrf_crypto is not supported...
I tried to deep dive through the macros, api abstractions and other layers but couldn't figure it out. The closest I got is this:
void debug_uart_print(const char * s) ...
Hi,
I have been evaluating the nRF5340dk for our application purposes and I am currently investigating on how the bluetooth directional finding works.
I happened to...
Hello Devzone Community,
I am continuing my long trek toward single-microamp operation of an nRF9160 based, custom board. On the LTE modem front I am making `AT+CPSMS=`...
Good afternoon.
We have an issue which we'd like to prevent, but suspect it may entail changing the out-of-the-box MCU Boot / SMP BLE code / process.
If we flash our...
Hello, I developed a custom PCB that uses the nRF52810 microchip, and I wrote a firmware that needs to use three RTCs.
The program is supposed to wake up the CPU by an RTC...
Hi there, i have a thingy91 for the electromaker contest. I've flashed the nrf51 bridge firmware using MCUboot. All went well. However, when i try to put in DFU mode the nrf9160...
Rookie question.
Finally I put my ble working passing a number thanks to the support from this forum. But now my problem is how to send a string with around 100 characters...
Hello nordic team, Question 1 How can I customize the Asset Tracker v1 to send Asset Orientation "FLIP" in the same frequency as the temperature and the rest of the values...
When communication fails on NRF connectivity dongle (In Python via pc_ble_driver) and Error code: NRF_ERROR_BUSY is received on attempts to write and one restarts python script...
Hi,
I am following below link for DFU over BLE. Link ( https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu ) currently it is working fine...
Hello ,
I'm using the libuarte library so i can send data and receive it , i'm enabling RTC2,TIMER1,TIMER0 and TIMER2 .
this is the main definition of my libuarte NRF_LIBUARTE_ASYNC_DEFINE...
I'm running into an odd problem with the PWM driver. We're using SDK 17.0.2 and the S113 softdevice on an nRF52833. We're using the PWM module to drive some LEDs.
The nRF52833...
