Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I am developing FW on NRF52840_DK for a BLE Peripheral as a Reader.
Reader to Mobile App Tx size is 32 bytes
Mobile App to Reader Rx size is 133 bytes.
When...
Dear Bluetooth Mesh experts, The firmware contains a proprietary message that sets a node's parameters and returns 100 bytes of data. The Android app sends it as an acknowledged...
Hi
I've configured Zephyr to run BLE host on cpuapp and BLE controller on cpunet, and using RPMsg to communicate between them.
When I call bt_enable() from the app core...
Hello,
I was wondering if there is a way to extract the "Device name" from the scanned advertisement data published by a model on a different node. I want to display the...
Hello ,
We are attempting to use the QSPI driver with an MX25 with 2 i/o lines instead of 4, essential SB 10 and 15 on the nrf52840 DK have been cut. However I am not...
Since the APP CPU memory is mapped at 0x2000.0000 in the perspective of the NET CPU, we understand that r/w access is possible for data. Is it possible for the NET CPU to...
I have a vendor model bt_mesh_model_op defined as follows
const struct bt_mesh_model_op _admin_model_ops [] = {
{ BT_MESH_MODEL_OP_3 ( OPCODE_SET_UNACK , VENDOR_ CID...
After several months of attempts, I was finally able to load, build, and flash the code from multi-NUS-master.zip using the VS version of nRF Connect, onto the nRF52840 DevKit...
Hello Nordic support team,
We are now creating a BLE central device which is part of a medical equipment.
The BLE communication works fine, but we want to add a BLE...
i'm writing a code for mic without using i2s because that mic will generate digital pdm signal.
i saw there is no solid code for low level driver or hard coding
Hi I want to set up a simple uarte communication between a NRF52832 and a faulhaber mcdc 3002s motion controller using the libuarte. I have max3232 logic converter in between...
Hello,
while migrating our FruityMesh framework to SDK17 I went through all SDK and SoftDevice release notes and migration documents and saw the following:
Now, to...
Hi Nordic Team,
Few questions about Power supply supervisor block of nRF52810. My device's supply volage (VDD) is 2 volt. I have enabled POFCON and the handler is getting...
Hello. I am designing an application where the goal is to send a notification, sleep for 1 second, send another etc.
To do this I used the application designed in this guide...
Hello,
I'm working on KX132-1211 accelerometer with nRF52832 and am using I2C(TWI) protocol. For that I need to create driver files even I was contact with manufactural...
