Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello!
I'm currently working on an IoT device that is supposed to send data to the cloud using MQTT with a TLS layer. We got this working in Norway using LTE-M and the...
Hi,
I am supplying my nrf52840 with5V on VBUS. I know that this does not actually provide the board with power, only the USB interface.
Based on the documentation, I understand...
Hi everyone,
I have connected a potentiometer to a GPIO pin (AIN2) and would like to show the varying values in the battery service.
I was wondering if there's any way...
environment:
SDK14.2 Project: ble_app_uart
I am sure that the problem occurs in uart_module.
Uart use the app_uart_put to send the first byte successfully, then it will...
We have already developed a wireless sensor application based on the ESB protocol.
Now we want to increase the range by adding an nRF21540.
We started by testing the sample...
Hi,
Is there a possibility of race condition when writing and reading using nrf_fstorage_write and nrf_fstorage_read?
I have a very strange bug, when writing to an address...
I am using VScode's extension for nRF connect. I have been using it to flash program with the 52DK and 9160DK previously. Now under the connected devices tab nothing shows...
Hi,
I'm using the GPIO mode of CAF leds module to control led.
LED_EFFECT_LED_BLINK or LED_EFFECT_LED_BLINK2 macro can be used to set the effects of led. But the loop_forever...
I encountered problems in developing nrf5340 with nck v1.5.0.
I use nrf_rpc_tr_init(rpc_receive_handler) to initialize an RPC and IRQ_DIRECT_CONNECT(I2S0_IRQn, 0, custom_i2s_irq_handler...
The solution seems to be built for a Production rollout for organizations with resources, but not so much for devs on a tight budget.
The actual bridge build is quite extensive...
Hello,
I'm using nRF52840 and nRF Connect. I've customized hello_world sample from Zephyr to also work with mcumgr and receive and respond to SMP commands such as "echo...
Hi,
I have been using an UART connection for serial communication but it stops working when I enable the Bluetooth module and initialize it. The error I receive is the same...
Hello, in an effort to downsize the EC2 instance from t3.small to t2.micro (nrfcloud-mqtt-bridge/MqttBridgeCluster/DefaultAutoScalingGroup), the bridge instance is detached...
I have adapted and incorporated the NCS OTA DFU sample into my project. Initially, FOTA updates have been working. Now, after pushing an update, the image is stuck pending...
Hi,
We are making software for our custom board based on nRF52833 and nRF5 SDK 17.0.2. We use app_uart for our serial communication in active mode and in sleep mode we disable...
