Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi as I can see many other also experienced problems installing nrfutil. I spent 5 hours trying Windows 8.1, Windows 10 and a Debian Linux box. I'm no python expert and I...
Hello,
I'm working on a project related to DWM1001-DEV at University of Illinois at Urbana-Champaign to build a demo of the product that uses UWB. However, I'm having several...
Good day
Please assist, I had my power profiler (PPK II)and Bluetooth dongle both plugged into my laptop. I accidentally upgraded the firmware for power profiler (PPK II...
Hi
I am using NRF5340dk with NCS version 1.5.0, I need to port the below library which was written for nrf51.
github.com/.../ADS1231
KIndly, Help me to resolve this...
I am using SDK nRF5_SDK_15.3.0_59ac345 with nrf32832. I want to write data from central to peripheral characteristics. I wrote below code:
Everything worked fine when...
I run the program step by step, when execute NRFX_IRQ_ENABLE(SAADC_IRQn);, it will go to app_error_fault_handler,.What's wrong ? I have do nothing with it!
I am trying to set a timer pulse at 500kHz and on every high pulse i want to do a read on another pin.
I have an IC HX711, that has a 24bit output MSB. every positive...
Hi,
im a beginner and i have problems to integrate the Homekit SDK in the Connect SDK.
Maybe anyone have a link to a tutorial?
The implementation by west has no effect...
Hi, Q1) I am facing an issue with the heap memory. I am using the Cjson_Parse function which uses quit a lot of memory. So I am wondering if there is a way to increase the...
Hello,
i m working on usbd example on nRF52
i have a problem that usbd stops sending data aftew few time. the port is still enabled but the data is not sent! any proposition...
I am trying to communicate with a sensor that has some interesting timing requirements for reading information from it, it requires ~100us delays between the address to read...
I want to calculate the power consumption used by many peripheral like GPIO, TWI, UART, SPI, RTC, SAADC. I can't find these information in nrf52840 PS v1.1
Because I don...
Hi, On my Windows 10 machine I've installed nRF Connect for Desktop (v3.7.0) and then used Toolchain Manager utility for installing nRF Connect SDK (v1.6.1). Afterward, navigating...
Hi,
I'm working on a project using BLE via s140, everything was working fine until I wanted to implement usb.
I created a blank project in order to validate the usbd then...
Hello, I have and audio source and i would need to divide it beetween two frequencies (<95Hz and >=95Hz).
Im trying this thing with a nRF52840 and i was looking at DSP libraries...
