Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
I am currently running some tests on the Legacy DFU protocol and notice that even valid firmware images are unable to be transmitted. My setup is as follows:
Peripheral...
Hello,
As shown in the question. I am testing the ncs bootloader b0 and mcuboot, but I don't know it's ok or not.
work condition
ncs: 1.6.1
board: PCA10056
I am...
Hi
I have a strange question to ask for your help.In my program, I define and use a large number of global variables. However, when I define a global variable again and...
Our application frequently changes the channel table when we find interference in multiple channels. So changing channels frequently (because of high interference) causes...
Hi,
I'm evaluating BLE power consumption with a PCA10040 nRF52DK and a PPK, I cut SB9 and did nothing else with DK.
No peripheral is used in projects, Buttons or LEDs...
Hello
I've read several post about the problem regard the printf and float numbers, such as this ( https://devzone.nordicsemi.com/f/nordic-q-a/30535/nrf52-printf-float-in...
Dear sirs/madams
I am using SDK 17.0.2
Situation:
One Central unit (nRF52840) and one Peripheral unit (nRF52840) have established a connection (NUS service).
When...
I plan to buy some nRF5340 . I only see 1 chip image from the Nordic Official Website . However, when I clicked on " distributor ", I saw nRF5340 has many different part numbers...
Hi Nordic team,
I am trying to implement DFU over uart in nRF52832 using SDK 17.0.0. My device has nRF52832 and main MCU in it, and I would like to do DFU from main MCU...
Hi
I play with watchdog.
After a watchdog reset the debugger does no longer stop on a breakpoint or generate a hardfault on a __BKPT()
How can I config the Chip to handle...
I have tried nrf_mesh_disable(); but it does not turn off the Provision Beaconing.
mesh_provisionee_prov_listen_stop(); does the trick, however I am struggling with re-enabling...
Hello
when hardfault is happaning, I can catch and understand the reset reason easilly, by looking at the map file
however, from time to time, I get a reset without...
I'm using Segger Embedded Studio version 1.6.0 to try to do some testing with SPI for a future project. Currently I am adding SPI functionality to the "Blinky" example: I...
#define SCAN_INTERVAL 0x00A0 /**< Determines scan interval in units of 0.625 millisecond. */
I am a beginner in this field. I am not sure what does this hexadecimal number...
Hi team:
After my device runs normally for more than 10 hours, the issue that THE socket cannot be created occasionally occurs. Once the issue occurs, the socket cannot...
