We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi,
I am trying to set up a secure boot chain on nRF54L15dk with NCS 3.2.3 and an upgradable bootloader .
My intended boot chain is:
B0 / NSIB
S0 / S1 for the second...
Hello,
I would like to implement Device Firmware Update (DFU) over NFC.
Is this supported, and is there any recommended way to implement it? Are there any examples, reference...
I have two nRF52840DK boards that I was working with recently.
PCA10056 3.0.2 2024.33
I flashed one board with a BLE peripheral device code from the nRF connect sample...
Hello,
I'm using dmic module for sampling audio data from microphone. Recently I updated NCS to 3.2.2 and I started observing the following log: "Failed to allocate buffer...
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
Hi,
We are migrating from NRF52840 to NRF54L15 (QFN48).
I am using nrf54l15-qfaa-reference-layout-0_8 as reference but really struggle to understand some design choices...
Environment:
Board: nRF54L15DK ( nrf54l15dk/nrf54l15/ cpuapp )
NCS Version: v3.1.0
Zephyr OS: v3.7.99 (NCS fork) NOTE: I am building this over peripheral uart example...
Hi,
I am developing with NCS 3.0. In my application, I need to use MD5 to calculate a signature. Following Nordic AI's guidance, I enabled CONFIG_PSA_WANT_ALG_MD5=y in prj...
Hi,
I have got nRF54LM20-DK with the nRF7002-EBII add-on. I would like to know is there any recommended camera add-on for this hardware to develop vision based AI solutions...
Hi,
I'm developing a custom board based on nRF9151 (similar to Thingy:91X) and trying to connect to nRF Cloud for location services (A-GNSS, Wi-Fi location, Cellular...
Hi,
I'm working on a project using the Thingy91x for prototyping. I'm using A-GNSS from nRF Cloud and although this is working, I'm not sure of the correct order of commands...
Dear support team,
I'm using:
nrf9151
nRF Connect SDK v3.2.3
I'm currently working on a project where I need to use MQTT and CoAP simultaneously, it works for...
