Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Dear sir,
Good Day!!.
Im using nrf52840 SDv16 and im using Ble_app_uart code, here with i need to add Bluetooth pairing request with password on my android mobile...
Hi,
I try to run the example project "ble_app_hids_keyboard" on a NRF52811 (I use the PCA10040e project, adapted to the NRF52811 on a custom board)
and I always run in...
Hi,
I was reading the values from the FICR of my nrf9160 on my thingy91 and I noticed that when I read the INFO.PART register from the FICR, it returned 0x00009120 rather...
we have BorderRouter- Raspberry pi flashed with nordic alpha 4.1.0.1 image + nrf52840 dongle in NCP design .
As an end device I have EFR32 MG12 WSTK flashed with OT-CLI...
I am developing application with buttonles BLE DFU and FreeRTOS. I needed debounce on buttons and decided to use app_button. Here is my init:
I turn on log debug on app_timer...
Apologies for this question, as it has been asked a number of times but I've not found anything to help so far.
As at the time of writing, I believe I've got the latest...
I'm trying to deploy a new firmware to my hardware device but I get the following error in the nrf Connect 3.6.1 programmer (v1.4.8):
16:47:36.937
Error when getting...
Hi,
I noticed that the PPK2 turns off the internal voltage regulator upon disconnecting from it. Is there a possibility to change that behavior? I would like the voltage...
Hey Guys,
I have the nrf52840 as the peripheral and my application use varies depending on which central I am connecting to in terms of:
PC ( Windows or macOS or Linux...
Hello,
I have been recently trying to initialize fds in my application, through the assistance of the given flash_fds examples in the SDK (15.3).
Currently, I'm coming...
Hi, I'm working with flash, I've started with the example code from flash_storage, as I will need to use flash while using a SoftDevice.
I use NRF52 Dongle and SDK17.0.2...
hello,
i am using nrf52840 dvk with sx1276 lora modules and trying to read my device address using spi i am just calling the below function in main
uint8_t spiCommandData...
Hello everyone,
I'm currently working on porting a device driver to Zephyr on the nRF9160. I have defined a device tree and set up the device through the .overlay file...
Hi
I was wondering if there is any further reading about the Automatic network selection set as <mode> in the +COPS set command.
Especially, I'm looking for a solution...
