Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello，
Purpose: Adjust 5340 frequency offset.
I want to use software adjust the internal load capacitance, but I don't know how to do it.
I found this below.
Can...
In a project using NRF52832 and SDK V15.3, we're having random crashes which have been isolated to a NRF_ERROR_BUSY (17) in components/libraries/log/src/nrf_log_backend_uart...
Hi, I am trying to do unit testing of my application, but at the moment I am not able even to compile and run a test of the example. I am using ncs v1.1.0 following this example...
I downloaded the following repo from github: https://github.com/NordicPlayground/ncs-display-ble-example , applyed the patch and i uploaded the scketch to my nRF5340DK , but...
Good Afternoon, I recently got an nRF5340 PDK kit and would like to get OpenThread examples for this board.
If possible I would like to demo the OpenThread CLI example....
I'm using this code to handle interrupt and power down the device. However, this code is not working the softdevice.
I just want to power on and power off using an interrupt...
Hello,
I am working with the nrf_cli_ble_uart (SDK16), I am able to connect, exchange data, however when I disconnect I got an assert :
It is indeed in ble_nus.c ...
Hi Nordic Team,
I am using a simple GPIO (tx/rx controlled via GPIO) FEM (PA/LNA) with connected to nRF52840.
I know I am allowed to crank up the TX power of nRF to +2dBm...
Is there support in NCS for MCUboot images encrypted with a different encryption key (not the same key as the signing key)? How is that configured (via prj.conf, etc)?
Hi, I have a nRF5340 based target board running SMP server plus MCUmgr. My ultimate goal is to reproduce on Windows the DFU over serial I already do from Linux. Tese are the...
Im trying to interface ADXL345 with nrf52DK via I2C. Im using the reference drivers in below link
https://devzone.nordicsemi.com/f/nordic-q-a/40822/adxl345-and-nrf52832...
Hello,
I am trying to connect a BLE HRM strap with nrf52382 using example/ble_central/ble_app_hrs_c/pca10040/s132
I am getting this on debug
<info> app_timer: RTC...
Hi,
I am having issues programming my custom nRF5340 board and was hoping to get some advice on the issue.
When programming using nRF Connect for Desktop (Windows 10,...
Device nrf52832 Custom board and nrf52DK with nrf52832
SDK 17.0.0
IDE Segger
when SPI interface is initialized by nrf_drv_spi_init, then MISO line behaves as follows...
