Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi,
I'm trying to find a way to power down and on again a RAM section, but I haven't had any luck finding.
In the SDK examples, there's a RAM retention example only, but...
Hi! I am using nrf52832 with icm20948 (SPI) and I want to put nrf52 in sleep and wake up if there's any motion detected. I am unable to put my device on sleep by the function...
I use nrf_libuarte_async from nRF5 SDK v16.0.0, without softdevice on nrf52840. The idle power consumption of my board is several tens of uA. I call:
and then the idle...
nRF52840, SDK16.0.0, S140v7.0.1
We use SoftDevice (RTC0) and app_timer (RTC1). I'm trying to configure RTC2 and TIMER0 to do PPI-driven crystal timing as described in...
I'm using the empty_app_core project for the APP CPU and my NET CPU binary does not start. I suspect the NETWORK.FORCEOFF is holding the NET CPU in reset upon startup. I tried...
I have encrypted 12 bytes on the nrf51 and sent this + 4 byte MIC across to an Android device.
However, when I try to decrypt on Android using a Cipher with "AES/CCM/NoPadding...
Hello everyone,
I would like to developpe my own custom board, I would like to know if it's simple to replace micro USB by USB C and if someone has already do that to help...
A.
while (true) { while (app_usbd_event_queue_process()) { /* Nothing to do */ } if(m_send_flag) { static int frame_counter; size_t size = sprintf(m_tx_buffer, "Hello USB...
hello I am using nrf52832. I am advertising some data and scanning (on the same microcontroller) for other nrf52 devices(which will have the same firmware). When the other...
Hello,
I'm using SDK v16.0. I'm trying to change the default UART pins from 6,8 to 45,46. In the pca10056.h I have made following changes.
But I still see log on pin...
I am using nRF Connect 2.3.2 on iOS 13.6 on an iPhone 11 Pro Max. I can scan and find my nRF52-DK with the flashed application and the service is correctly advertised (e.g...
Hi, I am using 2 x NRF52840 Dongle, When I program one of my dongle with NRF SDK 17.0 example blue ble_peripheral>> App_blinky it works fine and gets connected to nrf connect...
Hey,
I am using nRF51DK and have used it to print logs for debugging (via RTT)
If I wish now to have a full terminal capability, and to write to the nrf51422 as well just...
Hello,
I am learning to create library in segger. I am using segger example https://wiki.segger.com/How_to_create_a_library_project_and_use_it_in_executable_project
I...
Has anyone managed to get arm-none-eabi-gdb to work with Segger Embedded Studio?
I'm trying to use a Black Magic Probe with SES. I can connect to the nRF dev board with...
