This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
we have designed a board using Nrf9160 IC and we have issue with SIM module. we not getting 1.8 volt in "SIM_1V8" pin. when running mqtt sample program we are getting
...
Hi,
Using nRF52840 with SDK15.0.0.
I started my projetc based on BLE tutorial characteristics.
I created my service and add 2 characteristics successfully.
My module...
Hi All,
Sanity check here. I'm reading the RSSI value from a received packet
if (nrf_esb_read_rx_payload(&rx_payload) == NRF_SUCCESS) { if (rx_payload.length > 0) {...
A device that is provisioned with PB-GATT enabled stops receiving mesh packets after the provision is complete.
When the provisioning process is complete nrf_mesh_disable...
HI,
I got the following log while advertising:
SOFTDEVICE ASSERTION FAILED AT 0x00014AA6
Since this address locates at softdevice, I can not know what happens.
Would...
Hello,
Using nRF52 DK boards, I'm trying the simple_message_model by modifying the light switch example.
With the client, I simple send a 12 bytes unreliable message by...
Hello! I have a question about nordic thingy 52. Is there any possibility to play more than 8kHz on this board? For example: if i will change speaker on another it could help...
Hello, How do I set the analog reference voltage to external pin P0.02? I'm using the arduino environment so I don't know how to set it via those registers? I'm currently...
Hi,
I am using SDK 15.0 on a custom board using nRF52840. Softdevice is 6.0.0. Coding with SES.
I am investigating and trying to fix the infamous IOS caching of characteristics...
In the schematic of the nRF52840-DK L1 and C4 form the matching network. C22 is noted with NP, but on the DK i have, is a component placed.
Since i would like to use the...
Hi to everyone!
I've been testing the Bluetooth on the nRF52832 DK board with some of the examples and I have saved the mac address (obtained from my smartphone).
In...
Hello All,
I was wondering if someone can confirm the consumption of the nRF52840 in SYSTEM ON when running the Power Management Example on the nRF52840 DK board (in nRF...
My end object is to connect the peripheral to one required central. It should not get connect to another central or to the nRF connect app.
I have gone through many example...
Hi everyone ,
I'm looking for the ULPMark score for the nRF52840.
On the EEMBC website, I 'm seeing that Nordic Semiconductor is a partner, but I don't find any information...
Hi,
we are late stage development on NRF52840 with sdk 15.0 and softdevice 6.0. The mind turns to certification. It all seems very complex and confusing
1) Do we need...
