We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi there
I am currently trying to retain the RAM that is being used by the Softdevice. More precisely the attribute table so that its content does not need to be set after...
i am trying to connect multi peripherals to single "central" and i am using nrf52832 as central, I am using multi link central example for multiple connections but i am not...
Hi!
I am in the process of creating firmware for a product based in nRF52 because the firmware that comes with it does not fit my needs. So I am in the begining of the process...
Hi, I'm new with the Nordic, looks fin but I can't find application command interface description for the PC_BLE_Driver.
Background: I have a running application supporting...
SDK 12.3
nrf51 DK
ARMGCC
Windows 10
I'm trying to switch to gcc. I use 4.9 2015q3 version as recommended.
I have a trouble with simple blank blinky project (nRF5_SDK_12...
Hi,
I update the nRF Connect SDK to the latest version.
I switch SW5 to NRF91 and then erase the flash in nrf91 by using command nrfjprog –eraseall.
Then I use SES...
Hello All,
I am working on nRF51822. I am use IAR and nRF51 SDK 12.3.0.
I want to simultaneously read the value from 2 analog pins. For this, do I create just one adc_init...
Hello, I'm practicing this blog; Segger Embedded Studio - A Cross Platform IDE
on the following environment.
64-bit Windows 10 desktop
SEGGER J-Link 6...
Hi,
Recently we upgraded from NRF52832 to NRF52840, and as the Development seems to come to an end, one of the last features we need is OTA capability.
currently I am...
Using SDK 15.3.0 and S140 v6.1.1, would it be feasible at all to synchronize two nRF52840 modules, each only radiating in an oposite direction, in such a way they would alternate...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Dear Sir/Madam,
I have interfaced NRF24l01 module with LPC1768. Then used example code from Github for Intial configuration of NRF24l01 using LPC1768. checked waveform on...
Hello,
I have a problem with ble_peripheral examples.
Im using Embedded Studio V3.40 and I setup it like in this tutorial: devzone.nordicsemi.com/.../segger-embedded...
