We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
As a brief introduction, our research group uses bluetooth advertising to broadcast commands and responses between end devices and 'routers' which are connected to a PC. ...
Hi,
BLE Application on nRF52840 (pca10056) development board is being developed.
Application stopped the advertising to make device non-discoverable.
After that trying...
SDK 15.2, API 6.1
I have 1 firmware and 2 PCB it operates. PCB A was an external crystal and the sdk_config file is setup for the operation. However, PCB B uses internal...
I would like to communicate with and existing product that has the ability to communicate thanks to a UART-Bluetooth module. This module uses a Serial Port Profile and shows...
Hi,
I'm working on a thread network and I have some difficulties to configure the BorderRouter.
I use the BorderRouter V2 rapsberry image from Nordic, I recompile the...
Hi,
I want to be able to update the bootloader along with the application via OTA DFU. I know I can't generate both the application and bootloader in one image/zip so I...
I am looking for specs for the input impedance of the comparators (COMP and LPCOMP) for the nRF52832. I searched the forum and all I found was someone saying it is ">1 Mohm...
Hi,
I am trying to incorporate flash storage library to ble_app_uart_c example. I have added all necessary functions from ...\examples\peripheral\flash_fstorage.
When...
Hi everybody
I have a couple of questions regarding power consumption for the 'nRF5_SDK_11.0.0_89a8197' (nRF52832).
I currently have an application which use 12-bit SAADC...
Hi, I made a simple diagram of what my device should do:
The nRF52840 should receive data via SPI from another controller, mathematically process this data, and output...
Hi,
I just pulled the source code of 'nrf' from the git server (SHA1 ID: 383da27cc232bd7baa353e965b7fe8fa08b56d77).
After performed 'west update' to sync other repos,...
Hello!
I want merge and write via SWD full firmware, including: main firmware, bootloader, settings page.
When I start debug, all data correctly writed, but main firmware...
I am trying add UART functionality in nRF5_SDK_11.0.0_89a8197\examples\dfu\bootloader.
After adding all required files and compiling program I am getting following error...
Hello,
My device has GATT data attributes configured to have BLE_GATTS_VLOC_USER so the data are in application stack. In this way, the softdevice has direct access to the...
I've been trying to use the Adafruit nRF52 library ( github.com/.../Adafruit_nRF52_Arduino) and the Arduino IDE to program a nrf52832 using my nrf52840 DK. However, I keep...
