This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi,
(SDK 14.2 , S140 v5.0.2-alpha)
I followed the example in sdk v11 multiactivity_beacon : \examples\ble_peripheral\experimental_ble_app_multiactivity_beacon\hrs_advertiser...
I am using the nRF5_SDK_14.2.0 with two PCA10040 boards. ANT+ HR simulate from ANT+ simulator tool with ANT+ USB dongle.
Test 1 : SDK sample ble_ant_hrm_pca10040_s332...
Hello.
I have a situation that when upload the softdevice, application and bootloader for some reason stays in the bootloader after some debug I found that we enter in...
Hi,
i'am using nRF52840 (S140 v 5.0.2-alpha) DK and SDK 14.2.
i'am trying to create an application for Beacon which can advertise on 2 different MAC adresses, is it possible...
Hi DevZone,
I am working on a CAN Bus library for communication between nRF52840 Preview DK and MCP2515 chipset. I am trying to modify base on an Arduino MCP2515 CAN Bus...
I am using SDK 14.1.0 S132 for PCA0040 board
i want to combine the next two examples:
examples\ble_peripheral\ble_app_buttonless_dfu
and
examples\ble_peripheral...
Dear experts,
How is the UCIR protected against rewriting?
I would like to store some ID's which I want to be sure they cannot be erased or over-written once programmed...
Hello,
I can see s110 api commands as a web pages on infocenter.nordicsemi.com .
Is it an api list of commands manual in a document like pdf, etc.?
Thanks.
We are trying to configure the I2S peripheral for working with the ICS-43434 microphone ( www.invensense.com/.../) , but we are having a hard time fulfill the requirements...
The product spec is not clear, what is the maximum current draw possible from a 52832? Please assume ALL features are in use and fully enabled.
Thanks.
Hi Dev Zone,
I am going to communicate my nRF52840 Preview DK with an arduino shield. I am checking the PIN number. According to the information about the Arduino board...
Hello, I want to switch the functions between beacon advertising to connectable advertising.
In the code , it can be initial as a beacon advertising or normal advertising...
Hi,
I am running the ble_app_beacon example in nRF52 DK (PCA10040). I can see the nRF beacon in nRFConnect app - but not in the nRFToolbox - Beacons. After opening the app...
