This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I'll try to simplify my project as much as possible to make this understandable.
I'm wiring an nRF52 PCA10040 board to an iCE5LP (Lattice) FPGA.
I'm having an issue with...
I have an after market breakout board for nrf51822 with a usb-to-serial chip (cp2102) that I bought from Amazon . It should act as an NRF51 USB dongle (pca10031-like) but...
My pc server should send information to nrf52832 by ECDH, then I create a dll file from micro-ecc. However,the result in windows is not the same as the result in nrf52832...
dear friends ,
within a peripheral connection event, 9 states is identified, as it is shown in the pic above(from s132 document). Can i get a detailed description about what...
Hi @ all,
I am working with IoT SDK 0.9 and nRF52DK.
I have trouble with the lwIP CoAP client example.
Everything works so far, the board is connected and I'm able...
Hello! I am using a custom board that contains a nRF52832 device. The board has the SWDIO and SWDCK lines connected, which I have successfully been using to flash and debug...
I'm migrating to the new 13.0.0 SDK and I'm wondering what are the benefits of using nrf_serial over app_uart (if any) and what steps I would need to take to switch over if...
I have successfully manged to achieve serial communication between my PC (Windows) and nRF52 board by using the pc-ble-library and the pc-ble-library-js .
I can run without...
Hi, I updated nrfutil to use in new sdk 13, but when I type "nrfutil pkg generate --help" I can't see the code for Softdevice S132 v4.0.2 (0x98) as indicated in this guide...
I have done erase all thing.
But in the second step, I am getting following error.
nrfjprog --program s132_nrf52_3.0.0_softdevice.hex
ERROR: The --family option given...
Hello,
I'm following the steps listed in the nRF5_IoT_SDK documentation and would like to connect the nRF52 to my Raspberry Pi 3 router. I have the RPi3 enabled for 6LowPan...
Hi,
I have exactly the same problem as in question devzone.nordicsemi.com/.../
but I can't find the solution.
When I erase all from memory, debugging works. If I flash...
Hi
We have been able to set LE authenticated payload timeout via the following functions:-
ble_opt_t opt = {0};
opt.gap_opt.auth_payload_timeout.conn_handle = ValidHandle;...
Hi there,
I am currently using nRF52832 to communicate with a digital sensor ship. The sensor chip generates an interrupt every time when data is ready to read via SPI...
