But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
SDK: nRF5_SDK_11.0.0-2.alpha_bc3f6a0
Chip: NRF52
If I perform a TXTX transfer using the twi driver, it sends a repeated start/stop bit in between the two transmits. Is...
Hei,
I would like to compile ble_app_template example which is located in nRF5_SDK_v11 library. I get the following warning "Could not create/access path '._build' !" when...
Hi,
I'm using a timer to send message over uart.
Here is the initialization code:
err_code = app_timer_create(&m_uart_timeout_timer, APP_TIMER_MODE_SINGLE_SHOT, uart_timeout_handler...
I'm hoping this is just something silly that I've overlooked, but I'm running into an issue: Whenever I try to prompt the scheduling of a TWI transaction an error occurs ...
im using sdk10 softdevice 8.0.
on my app I configured #define APP_ADV_INTERVAL 1500 and I noticed that when I activate Dfu service (activate notification on last service...
hello,
I am trying to direct advertisement on NRF51822 board.When giving the peer address i am confused that how to specify the address type of the device, whether BLE_GAP_ADDR_TYPE_PUBLIC...
Hello,
I made 10 custom board with nRF52 rev C, epson 128FA 128 32 MHZ, epson FC 135 32,768 KHz
I have some difficulties to get crystals working.
10 of the CPU run...
Hello!
I've developed a board with NRF8001 module mounted on it. Antenna on the board is much longer than in reference designs, so I can change the length. I also can add...
We been developing device based on NRF 51822 (NRF51822-CFAC-R) (62-UFBGA, WLCSP).
We plan to use 2032 battery, and need at least one year of autonomous BLE work, our device...
Hi,
As discussed here a way to advertise each 20msec is changing the mode to BLE_GAP_ADV_TYPE_ADV_IND. This is a connectable mode and assume we do not want a connection...
why I debug the project ble_app_hrs_rscs_relay in SDKv10\ble_central_and_peripheral\ , it can not go to main(), always stay on first,I do not change anything, it compile oK...
Hello,
When I restart my application with debugger, i have strange IRQs called (TWI, ...) before init. Possibly IRQ still active and debug don't touch them.
Can I disable...
Can you please provide an example on how to read 10kB from the internal flash using pstorage_load and send it to mobile phone (NRF Toolbox) via NUS UART BLE ble_nus_string_send...
Hi
I've just seen Nordic has ported FreeRTOS into the NRF5x series. Have you been using it together the S110? What's your experience? Could I use it together any SoftDevice...
