We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Got a Keil ULINKpro D debug unit with my Keil uVision\ toolchain license. However that doesn't seem to work with the Nordic nRF51822 on my Fujitsu module Development kit....
Hi,
I referred to the sample code "led_radio_example" and I think I might miss some thing so the program does not work.
The sample code indicates to use a terminal program...
Hi,
I am trying to understand the behavior of auto acknowledgement with payload for an application I am working on, I am hoping for some clarification on how ACK with payload...
I seem to be getting into sleep() fine with not able to connect to my app!
but getting back to work from sleep() is taking toll and its not working simply.
I'm trying...
Nordic will release a new development kit in april, named mkit.
It is based on arm mbed .
Writing a ble app will be easy, fast and simple using mbed BLE API .
My question...
Hello,
I compiled the pc10001/blinky_example with gcc/makefile, i can flash it with nRFgo Studio and it works. But if I try to compile/flash the pc10001/button_radio_example...
My computer is running KEIL MDK4 and nRF51 SDK4.
So far no problem with nRF51422QFAAC0.
Upgrading to Keil MDK5 would be a nightmare, so that I gave up after a few days...
Hi,
I'm trying the nRF UART example but I can't get it to work.
I have opened the uart_example project in uVision and loaded it to PCA10001.
Then I opened the Master...
I want to add timer to send sensor movement data to PC every 8ms(125HZ).
But when I add app_timer like normal
1.raise APP_TIMER_MAX_TIMERS
2.raise APP_TIMER_OP_QUEUE_SIZE...
I am testing Keil MDK5 and created my own simple nRF51422 project (not from the sample), hello world type of code. But the "download" button is disabled.
The J-Link is configured...
Hi,
Can anyone please tell me the exact way to enter into the bootloader mode by writing some characteristics with specific value.
I tried setting
NRF_POWER->GPREGRET...
The existing Master Control Panel cannot be used as an automatic test platform.
Basically I am looking to send commands via a tcp/ip which will invoke scan/connect/disconnect...
I'm trying to measure a scaled down battery voltage level on an ADC pin. Given my resistor values the voltage on the pin should be about 0.279 times VBATT, to fit within 1...
Hi Nordic guys,
How much is the current consumption of the LDO only (quiescent current), without DC / DC converter, in uA? How much is dropout voltage and PSRR (ripple...
