Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
My laptop does not detect my dongle after I program it through nrfConnect. I am thinking that maybe I have to reflash the pca 10059 firmware, but I do not have any nrf development...
Using nRF5340 hci code, I've been able to get a device that connects and authenticates with two central devices. However, after connecting with one central device, I no longer...
Dear Forum,
Knowing that nRF9161 SoC contains two microcontrollers: modem microcontroller (MCU) and application microcontroller (MCU):
1. Is it possible to check what...
I am developing a touch keyboard. (using SDK 17.1.0, nRF52840) Of course, this product connects to all OSes such as Windows/iPad/MacBook via BLE. However, there are keys that...
Hi there
For proper playback of LE Audio, it's required to get the current time of the Bluetooth Controller.
In the LE Audio examples (nrf/application/nrf5340_audio) on...
Hi,
I'm trying to get the PWM to work to operate a vibrator connected to the nRF54L15 PDK. I'm basing my activity on lesson4 - pwm as I'm also new to Zephyr (but experienced...
Hi Community,
I made a custom board based on thingy53.
the custom board can be flashed with nRF5340-DK, I see the " merged_domains.hex " is flashed.
Also tried with...
Hi
Default value of NRF_SPIM0->IFTIMING.RXDELAY = 02 based on the datasheet, but it always shows 0x00 on debugger and I can not rewrite it.
Has anyone entered the same...
I want to use the example of "Wi Fi: Shell" to set TWT parameters by referring to the official documentation：
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols...
I see that the NRF24L01P is not recommended for new designs.
Since this product is in our production currently, we want to now the following things
When will the NRF24L01P...
Hi,
I'm trying to build the ZigBee light bulb sample on nRF52840 dongle.
It compiles. 1 LED blinks, and the other 2 are steady, which supposedly indicates that the dongle...
We are using an nrf52833 with the nrf21540 FEM and are getting a fault. Even with a basic BLE example, we are getting this fault. When we use a board that does not utiliize...
I need to detect the VCC voltage on the nrf52833 on power-up and wait till it slowly ramps up to 3V. Is there a way to do this using the Power-Fail Comparator. I found another...
I am using an nrf52833 with both 32.768 kHz and 32MHz external crystals (identical to the DK). When I go down to -30 deg C, the uart stops working. I believe that this is...
Hi
I'm trying to use the nRF Cloud Provisioning Service with the nRF Cloud multi-service sample in SDK 2.6 on a nRF9151DK.
I have got the token from the device using AT...
