After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have an NRF52840 dongle programmed with the connectivity firmware and I want to use it as a central device to connect to a peripheral, and I want to set this up in Python...
HI,
I’m working with the nRF21540 and want to add a GDT, a series capacitor and a TVS diode to its antenna port to protect it against lightning surges and ESD. Could you...
Hi
I'm currently in the middle of porting our board from nrf sdk 2.6.1 to nrf sdk 3.2.1. I made it so far, that the correct dts are used, but somehow the build process seems...
I am following the instructions as per Getting Started with the Asset Tracker Template.
I have successfully created the environment and done the West Update.
When I do...
Hei,
I have nRF9151 SMA DK v0.9.0 running with board controller FW v1.1.0. This is stated by the Board Configurator v1.1.2 tool.
I tried to set both nPM VOUT2 and VDD...
Hello,
For my project I am interested in performing IQ sampling in the payload of a BLE packet, using nRF52833 at both receiver and transmitter.
I am manually configuring...
Hi,
We've been developing a product using nRF52840, where it does a lot of advertising and scanning.
We've migrated from SDK v2.5.2 to v2.8.0, and recently discovered...
nRF Connect SDK v3.2.1 on Windows 11
I am trying to build the Matter Light Bulb sample using a nRF7002DK but run it over Thread instead of WiFi (the default). Since this...
Good day,
When using the bt_gatt_discover() with a NULL UUID parameter, the code sweeps all UUIDs available from the start_handle to the end_handle. This is verified with...
Development environment: MacOS Sequoia (15.4.1), Visual Studio Code v1.108 0, nrfConnect 2026.1.1242
I am trying to develop a "workspace" project with a nRF52840DK as my...
I understand that the rf path should be 50 ohm coplaner to the output matching network that should be placed very close the the NRF chip. The recommendation shown in the reference...
I’m facing a Power Profiler Kit II (PPK2) measurement discrepancy that appears to depend on the host PC , not the target board or firmware.
Target setup
Custom board...
Hi all,
What is the increase in current consumption or power consumption when measuring RSSI with the nRF52833?
My device is a peripheral. I would like to estimate this...
I am using nrfx_nvmc_page_partial_erase_init() and nrfx_nvmc_page_partial_erase_continue() to erase flash in-between wireless connection events. The datasheet states: " The...
I have an IoT project that reads data from a proprietary device via an I2c SBIffer. The device consists of a controller and a small display, which are connected via an I2C...
