Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi
We are using STM32 board as a HOST controller and NRF9160 as cellular modem. On the STM32 board PPP client is running over serial interface.
We need PPP server support...
Hi,
I own an nRF5340 Audio DK, on which I successfully run the example audio application (in BIS mode).
I also have my own customized board, based on Raytac MDBT53v, for...
I have a nRF9160 custom board. I am using 2 UARTs (UART0 and UART2). I need to have an RX interrupt on both UARTs. I have identical setups and configuration and code. The...
We are using PC-BLE-DRIVER-JS for our central and zephyr in our peripheral (833). The central bonded with the peripheral only when the id (IRK) param in our central is set...
Hi all!
Hopefully this doesn't come off as too much of an ignorant question, but I'm having a hard time understanding the pinout of the Thingy 91 since I can't map where...
I´m trying to design a compact circuit for the NRF91, since i have limited space i´m planning to do a board stackup with the antenna board on top. Right now my board is 50mm...
I am working on an application where I am using 3 SAADC channels all with the same reference pin.
Upon startup, I will call app_sensor_init() to initialize my SAADC, timer...
The Commissioning and Characterization note for the nRF700x series ( https://infocenter.nordicsemi.com/pdf/nan_043.pdf ) says in section 2.1.2
However I have been unable...
Hi! We are considering moving from nRF9160 to nRF9161 on our custom board.
We are currently running modem FW 1.3.1 and nRF Connect SDK 2.0.2 on the 9160. However, we find...
Hello,
I am looking to conduct a test to simulate a Zigbee device using nrf52840 in the Zigbee:shell sample. This involves modifying the manufacturer ID and model ID. If...
I need a clarification about the update of gpiote driver. I've passed from the NCS 2.5.1 to the 2.6.1 and now I have issues in the configuration of my ppi infrastructure....
Hi,
I have a peripheral which is sending data to a central via the NUS service. Everything works as expected until the central is removed (e.g. power failure)
The problem...
Hi, basically I want to expose my firmware's version through the GATT DIS (Device Information Service) to client applications.
I have gone through:
the VERSION file...
The link provided as part of the webinar to download the PPT is not working, So could you please with PPT
Following is the webinar link
https://www.youtube.com/watch...
I develop using Apple M3 paired with VS Code with nrf extension. The development board I use is NRF52840DK. When using JLink firmware with version number JLink_V796b, the...
