But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi all, In my project i'm using the nrf52840 SoC in my board. I'm currently working on the bootloader, and I would like to add additional logic to functions mentiond in the...
Hi,
I am trying to train a few beginner FW engineers on RTOS concepts and have been using the Nordic training videos. However, sometimes, its tough to explain thread execution...
Hello,
I need to persist ~200K of data on the internal flash of an NRF52832 chip. I've run a memory report and I'm current taking up 185Kb and the chip has 512 Kb of flash...
Our project has been working on nRF21540 & nRF52833.
Let us have a method to reduce the power of nRF21540 under 400uA at idle.
Currently, without nRF21540, the power...
We started a new project using nRF Connect SDK & Zephyr. Installation of development tools is very easy and convenient using VSC add-ons. However, we are concerned about the...
Hi, we have a project where we want to track the location of a Thingy91 and send it to an nRF9160, a cellphone or/and a website. Do anyone know about any guides that could...
During a ble connection process using a nrf54l15 as a peripheral, I get an sdc fault "File 48, Line 203" with this callstack:
sym_476LRB5XNUARAHCHHC7ZAIGPFC5VZ4W2N4467LI...
Hi,
I'm building an application for the nrf5340 in rust and I want to be able to use the bluetooth LE audio functionality. For this I have two questions:
How can I build...
Hey,
I get the following errors when running my application and I am not sure how to debug this (The nrf thread viewer is empty when I start a debug session of my application...
I try to use one 5340 board as cis client to connect with Galaxy Buds2 Pro and can get the audio in headset.
But the connection is randomly disconnected, the log i get is...
"When I run the CDC ACM example to enable UART, it works fine. However, when I switch to another example that also uses the same USB configuration, the USB port is not visible...
Hello all. I have somewhat of a basic question to ask. I am looking for a USB dongle that can transmit data. runs off of the 5v in the usb and can connect to Win11 by hopefully...
Hi , We are developing a product with NRF5340-CLAA-R WLCSP package IC. While entering the PCB design stage we encountered an Issue with its footprint. First we imported Footprint...
Hello, I am utilizing a Laird (now ezurio) bl5340 module on my custom board which requires the internal 13.5pF caps to be set for the high frequency 32Mhz clock source as...
