Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
Hi,
The fstorage library is not available for NCS. Instead, the OS Service "Settings" should be used. (see the last answer of this thread )
In fstorage, it is possible...
I am working on a prototype using the nRF Connect SDK v2.1.0 on the nRF52 Thingy platform.
For my prototype, I need to store normal log output on the internal flash of the...
Hi,
We have to enable the radio shorts in our developing multi link firmware. ( We let any node connect to 3 other nodes at the max ( 1 as a slave and 2 as a master )) ...
Hi all,
I use GPIOTE and DPPI to read SPI data from IMU sensor. After IMU send out "Data Ready" signal, GPIOTE will be triggered and DPPI start to read using SPIM2.
And...
Hello ,
I am working on a project an nRF52840 + quectel BG96 modem. I am porting the freeRTOS cellular interface library for the Nordic platform and mainly the FreeRTOS...
Dear all,
I am developing a device that base on nrf52833, nrf connect sdk ver 2.0.0
The device run bluetooth mesh. And becase it was powered by battery, so it must go...
Hi there,
There are some problems when setting nrf52840 GPIO interrupt. When I use gpio_pin_interrupt_configure_dt api to configure 11 gpio pins then download to my customer...
Hi
I am testing <InstallFolder>\examples\peripheral\usbd_cdc_acm project, when I use serial tool of pc to open port, it can send or receive data.
but if I don't want to...
I wrote this function:
When calling it and
ptr points to something odd, the chip seems to crash. Can you not dereference odd memory addresses?
Or is there a different...
Hi,
I have been using nrf5340 audio dk fir the last couple weeks with nRF Connect SDK v2.1.0 and nRF Connect SDK v2.1.1. There were issues with the audio template for walkie...
Hi,
I'm using nRF Connect 2.1.1
I create a application based on 802154_phy_test template.
When I create a configuration and build for the nRF52840 it compiles OK.
...
Hello,
I have a TMP117 attached to I2C1 on a nrf5340 and am using the zephyr NCS v2.0.0 driver to communicate with it.
How can I configure I2C1 for power management...
