Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
I want to Enable and Disable Application and network core at some point in the mid of the code. What configuration would i be required to switch the cores or Enable/Disable...
hello,
i am using nrf52832 with sdk 15.2 i want to store signed int values in to nvs (like rssi and tx power) so that i can change these in run time
i can able to...
We are trying to achieve automatic scan and join in both LTE-M and NB-IoT network modes. We are using SICA B1 -SiP with modem FW 1.3.1, and %XSYSTEMMODE=1,1,0,0 setting. ...
I am developing a product that I have going into SYSTEM_SOFT_OFF to maximise battery life. I have a bunch of GPIOs (these are currently just buttons on the nRF52-DK) that...
Hello,
I want to test the throughput of Isochronous Channel using ncs sample code "iso_connected_benchmark". So far I can successfully build the code and run in central...
Hi,
I'm trying to save system uptime when the watchdog callback occurs.
The NVS functionality works when calling nvs_write elsewhere in code.
Calling nvs_write inside...
Other Configurations:
prj.conf
# General config
CONFIG_LOG = y
CONFIG_LOG_DEFAULT_LEVEL = 4
CONFIG_STACK_SENTINEL = y
CONFIG_NEWLIB_LIBC = y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Refering to following discussion:
mqtt-messages-received-multiple-times-on-qos-1-subscription
Our application is based on SLM application from nrf connect sdk 1.3.2. There...
Hi, I am using nRF52832 module (GAP peripheral, GATT server) with nRF5SDK, ble_app_uart_pca10040_s112 application.
In ble_app_uart application, how can I ensure that UART...
Hi,
I'm a real novice with this but I'm having this issue and I can't see how to resolve it.
Building HeartRate_sensor west build --build-dir c:\Users\deirdre.hackett...
hello Nordic
i am want to run an ncs based application (that is running on nrf52840, -> trying to create single code for 2 boards i have), when i set to run the same application...
Hi,
What are the geofence capabilities in BLE Mesh ? What are the possible features that can be implemented in the view of geofence. My point is like the mesh node if it...
Hi, All
I am trying the example here ...ncs\v1.9.1\zephyr\samples\bluetooth\central_multilink\ with nRF52833dk_nrf52833 board, however it doesn't build, and saying the maximum...
