Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Our startup previously used nrfx 2.4.0 but worked just fine. Upgrading to nrfx 2.8.0 results in a Hard Fault at the location seen in the screenshot. Which is the file located...
Hi,
I am posting this here because I am not sure exactly which repository to file the bug on (zephyr? west? something else?)
nrfjprog supports programming over IP with...
I'm still new to Zephyr, so this could be an easy question that I'm googling poorly - if so, sorry in advance. I just wanted to add an extra LED, led4 , to the existing nrf9160dk...
Hi everyone, and thanks for all the help provided on this site !
I have tried to flash a MDBT42Q using the nrf82832-DK (PCA10040) and it works fine for simple peripheral...
Hello,
Aim : Our application uses the PC-BLE driver for serialization purpose as well as the nrfutil for DFU purpose in the same script, we switch between the two by opening...
Hi,
I am developing a BLE sensor based on nRF52840 SoC (QIAA aQFN 73). I would like to get some clarrification regarding following points while hardware design. Thanks for...
Hi there,
We intend on using the default Serial LTE Modem example on the nrf9160 in our product. We will then communicate to the modem with AT commands from an external...
I'm trying to program a nrf52832 chip with a nrf52dk board by configuration below, referred to https://devzone.nordicsemi.com/f/nordic-q-a/14058/external-programming-using...
Hello,
Since the last update some of the includes in my files are being marked by VSCode as "cannot open source file xxx (1696)"
The application compiles fine...
Hi! The nRF9160 has a nice, accurate LFXO integrated. I'm assuming that it's also active most of the time anyway to provide timing for the modem (assuming one is using the...
Hi, I have the following questions. Please help me answer them: Using the protocol stack of the above version, one master and two slaves are disconnected when reconnecting...
Hello,
In my project i am using nrf52840 with my custom board and to upload the code through NRF_CONNECT application with soft device its uploading properly but with segger...
I'm interested to know if can I have the Zigbee protocol on the nRF5340 microcontroller and use a web browser (from my phone for example) and get a http page from the MCU...
Hi,
I've connected in BLE two devices
- NRF52840 DK as "central", connected to PC via nRF Connect For Desktop v3.11.0 -> Bluetooth Low Energy v3.0.1 - NRF5340 based custom...
Hello Sir/mam,
I am working on BMS I want to prefer nrf9160 dk board for my project . I want know is there any way or document available for communicate with Modbus or can...
