i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Is there any zigbee example for nrf52840 dongle (PCA10059) ? If not, what is additional changes needed to add support in existing examples?
I unable to run the zigbee switch...
Hi, I need to add Azure IOT connectivity to nRF5340DK. I have already tested NodeMCU based data upload to HTTP based server and successfully working. Now, to divert the data...
I am trying to upgrade SoftDevice and Application firmware from v6.1.1 to v7.2.0 on Nordic USB840M dongle and I am facing a strange issue after such upgrade.
Please find...
Hi,
I have created my own service and charecteristic
1. But i am seeing only unknown service - How to give a name to this service
2. I am getting unknown charecteristic...
Hi
I have compiled (successfully) the Zephyr example samples/bluetooth/peripheral example for the nRF52 DK (nRF52832).
I am going through the code and trying to understand...
Hi
I have developed a device using the nRF52832 and I am wondering if there is built in functionality to reset the chip back into bootloader mode without programming the...
Hi All,
I'm using SDK17.1.0 and I have a question about mobile device subscribe.
I asked this question before, but the engineer didn't reply, so I asked again, thank...
Hi All,
I want to port BPS to my custom project, I encountered the problem as the title.
When I connect and trigger the subscribe like this picture.
My project will...
I have code that runs for around 5 days, then for some unknown reason hangs or stops running, which makes it almost impossible to debug.
I have also tried to implement interrupt...
Hi.
I have an issue that, If I power off Master and do save flash at Slave side together, the nrf_fstorage_is_busy(p_fs) return value always true .
When BLE is connectting...
I added a mesh shell module to my firmware running on nRF52480 .
Opened the mesh shell
uart:~$ mesh init Mesh shell initialized
mesh provision 0 0x100 0
Crash (see...
Hey,
I have implemented BT FOTA process for my zephyr based application. DFU over Bluetooth works fine. But now I struggle to implement manual upload of image (it will be...
Hello Devzone,
My name is Ted. Recently I posted here and received some good help on low power sample code for the nRF9160DK board. This code helped me prove in real life...
I'm currently trying to set up a simple demo using 2 dev kits running the SPIS and NRFx_SPIM examples but the SPIS seems to always send corrupted data over the MISO line....
Hi,
I'm using two dev kits to test out some SPI firmware before I deploy it to our custom boards and I've been running into a weird issue where my SPIS sends out corrupted...
