Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi,
I am supplying my nrf52840 with5V on VBUS. I know that this does not actually provide the board with power, only the USB interface.
Based on the documentation, I understand...
Hi everyone,
I have connected a potentiometer to a GPIO pin (AIN2) and would like to show the varying values in the battery service.
I was wondering if there's any way...
environment:
SDK14.2 Project: ble_app_uart
I am sure that the problem occurs in uart_module.
Uart use the app_uart_put to send the first byte successfully, then it will...
We have already developed a wireless sensor application based on the ESB protocol.
Now we want to increase the range by adding an nRF21540.
We started by testing the sample...
Hi,
Is there a possibility of race condition when writing and reading using nrf_fstorage_write and nrf_fstorage_read?
I have a very strange bug, when writing to an address...
I am using VScode's extension for nRF connect. I have been using it to flash program with the 52DK and 9160DK previously. Now under the connected devices tab nothing shows...
Hi,
I'm using the GPIO mode of CAF leds module to control led.
LED_EFFECT_LED_BLINK or LED_EFFECT_LED_BLINK2 macro can be used to set the effects of led. But the loop_forever...
I encountered problems in developing nrf5340 with nck v1.5.0.
I use nrf_rpc_tr_init(rpc_receive_handler) to initialize an RPC and IRQ_DIRECT_CONNECT(I2S0_IRQn, 0, custom_i2s_irq_handler...
The solution seems to be built for a Production rollout for organizations with resources, but not so much for devs on a tight budget.
The actual bridge build is quite extensive...
Hello,
I'm using nRF52840 and nRF Connect. I've customized hello_world sample from Zephyr to also work with mcumgr and receive and respond to SMP commands such as "echo...
Hi,
I have been using an UART connection for serial communication but it stops working when I enable the Bluetooth module and initialize it. The error I receive is the same...
Hello, in an effort to downsize the EC2 instance from t3.small to t2.micro (nrfcloud-mqtt-bridge/MqttBridgeCluster/DefaultAutoScalingGroup), the bridge instance is detached...
I have adapted and incorporated the NCS OTA DFU sample into my project. Initially, FOTA updates have been working. Now, after pushing an update, the image is stuck pending...
Hi,
We are making software for our custom board based on nRF52833 and nRF5 SDK 17.0.2. We use app_uart for our serial communication in active mode and in sleep mode we disable...
I'm trying to build a basic shell sample on a custom board based on nRF52840
In the proj.conf file I have
CONFIG_SHELL =y
CONFIG_SHELL_GETOPT =y
CONFIG_SHELL_BACKENDS...
