Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
1. I'm runnig the asset tracker fine with nRFCloud. When I run the cloud_client, I get this log:
*** Booting Zephyr OS build v2.7.0-ncs1 *** W: Already initialized. Nothing...
Hi,
Referring to this - https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/reference/devicetree/bindings/net/wireless/nordic,nrf21540-fem.html I understand...
Hello everyone! I'd like to implement the nrf52-ble-image-transfer-demo with a nRF52840 Dongle, for a small low-power image transfer application. My question now is, how do...
I am trying to use Visual Code environment (on macosx Intel macbook pro) to program nrf52840 dongle.
The dongle is found and programmed with using nRF Connect for Desktop...
Hi Nordic，
One of my customer has a problem about 2M phy.
They use 52840 connected with IOS via 2M phy.
They set MIN_CONN_INTERVAL and MAX_CONN_INTERVAL both to 20...
Hi, I'm working on nRF9160 with Zephyr (SDK 1.7.1) and one SPI device. I analyze CS signal with correlation to SPI SCK. Is that normal that CS signal stays low much longer...
I am trying to add a Nordic Thingy 91 to my azure Iot hub.
i've configured the device according to the guide
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
I noticed when using the UART BLE Example that there is no password or pairing request to connect to and use the device.
Everything works fine, and I even implemented my...
I followed the official tutorial. The programmer 2.3.3 in nRF Connect for Desktop v3.10.0 in Linux has problems programming the nRF52840 USB dongle rev 2.1.0 in DFU mode....
Setup: Windows 10, nrfutil verison 6.1.3, python 3.10.2, nRF 5 SDK 17.0.2
I have a custom board running the stock DFU firmware from the nRF5 SDK. The only changes we made...
There are many questions on DevZone on modifications to NCS peripheral_uart/central_uart NUS example applications to support higher throughput.
We have been mostly successful...
I would like to use the nrf connect sdk to connect to a device and 'discover' the GATT services it supports, the characteristics in each service, and then read the descriptions...
Hi everyone!
I ported some project from NRFsdk 17.0.2 (all works fine) to Zephyr rtos and faced with issue - when set high speed uart (460800 - 921600) then some bytes ...
Hi All
A few times ago, I installed the nRF Connect for Desktop v.3.8.0 on my PC.
Getting started assistant, Programmer, Toolchain manager apps were installed and everything...
