Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Trying to flash firmware to nRF5340 cpuapp core with a sample from nRF connect sdk 1.6.1. I'm able to flash it to a PCA10095 dev kit. With EVM-BT40-V1 from Fanstel, I can...
Hi. I have came into trouble with nrfutil and the provided images.
I have a board that's connected via usb to the computer and I am trying to use the connectivity firmware...
In the nRF5340 user manual section 7.14.3, there is a note regarding assigning the same pin on more than one GPIOTE channel can result in unpredictable behavior. We have implemented...
Hello Jared,
the previous ticket find under the following link is locked. So I decided to open a new one.
https://devzone.nordicsemi.com/f/nordic-q-a/80312/uart-break...
Hi Nordic,
A important customer employ nRF5340 in their product, they are chosing the 32M crystal osciallor now.
Form the SPEC of 5340, if we want to communicate with...
I posted this theme, but the post is locked before fixed. I don't know the reason so repost. I'm sorry about this case.
-------------------------
Question:
I consider...
Hi,
I have a custom board with nrf52840 chipset that controls a GSM modem over UART, and this setup works just fine (zephyr project).
Now, I'm trying to replicate this...
Hi everybody,
I get this error trying to set coded_phy advertising on nrf52840 dongle. This is the code that i try.
The error that i get is:
That means I/O error...
I flash v1.7.0 at_client and mfw-v1.3.0 into nrf9160-DK board, LTE works normally and the board can get the ip. ( https://files.slack.com/files-pri/T0SBEQ7AR-F02J4REC8RX/nordic...
I'm trying to implement communication protocol that involves clock and bidirectional I/O line. Clock signal is coming from an external device and expected to be in 1-5MHz...
Hi,
Could you please help to fill which nRF9160 SIP revision fit for SDK?
nRF9160 modem firmware version
nRF Connect SDK
nRF9160-DK, SIP revision (BA, B0,...
Hello,
I have a question about the best way of implementation.
The data will consists out of a struct with multiple pressure and temperature measurements coming from another...
Hi everyone,
I have this question to ask. So I am trying do make an end device that run on low power. I can see that there is an example about the sleepy end device in the...
