Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I'm openning a new case (following the proposal of Einar Thorsrud ).
I want to do a BLE NUS project with custom service 128bits and with custom characteristics also...
Greetings!
Using the NRF52840 PDK, I succesfully erase, write and read without any modifications!
I have custom boards which involved a NRF52840 and a MX25R6435F (so same...
Dear Nordic Support,
My project is split into two parts: A firmware application that is based on the Generic Level Server model example (from the Mesh SDK) and an Android...
Good morning,
I'm working on nRF5 SDK v17.0.2 and I am using Segger Embedded Studios (SES) for the development.
I'm having a problem when I want to share my project...
I'm aware that the nRF CLI tools are not yet ported to AArch64 so they don't work natively on Apple Silicon. Normally rosetta 2 is fine, but nrfjprog is not compatible with...
working with nrf52832, sdk 16.0 s132 v7.01
in the uart example i get to this place in the code :
i get a pin toggle which makes my system do some unwanted things...
Hi,
I have a ARM based Linux host CPU connect to MDBT42Q-U(nRF52832).
But I cannot control it by BlueZ:
```
root@OpenWrt:/# btattach -B /dev/ttyMSM1 -P h4 & root...
Hello,
After some weeks of inactivity and moving my desk to an other address, the nRF connect application is not running and show a white screen for all applications except...
Just checking in, I am recently starting to develop cellular communication and looking to develop on the nRF9160. I have been in nRF52 space and with that I develop inside...
Hi, I'm using nrf52840 DK. In my project I want to receive audio from microphone (analog) and stream it to bluetooth headphones. Is there any possible way to do it? Any help...
Hi,
I have been working with a nRF52840 DK up until now, but I need to change and move to a nRF52833 DK. I wanted to adapt my code as they can both use the softdevice I...
Hi all
I'm working on a project based on the nRF52 chip and I'm encountering
If the system runs out of battery or no buttons are pressed within a timeout the system has...
Hello
I made an application on the nRF52 sdk, which works correctly.
Now I want to add the ability to update the firmware via OTA bluetooth.
I followed the instructions...
1. Using Zephyr, trying to config SPI_3 of nrf9160 more than 1MHz for flash interface.
2. Ending up in faults.
3. We need to configure SPI_3 as master with freq > 2MHz...
hello!
im using sdk 17.0.2 with softdevice s112 in our customized board as i want to work for long range mode,so i need extended advertisement ie no available in s112 so...
