Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi,
I am using nRF52840 on my custom board and Mesh SDK 5.0.0. I am testing the Mesh Light Switch example on my custom boards(one for client and two for server)with battery...
How can I send data from nRF5340 to Raspberry Pi? Do I need nRF52840 Dongle dongle attached to raspberry pi? What functions should be used to send from nRF5340 and receive...
Hi forum,
I am working on nrf52832 custom board, using sdk 15.0.0.
I referred example/peripherals/twi_sesnor example as reference. I am trying to interface LIS2dw12 with...
Hi,
I've stumbled upon a problem that I haven't been able to solve for an extended period of time. I've found several other posts on this forum describing something vaguely...
Hi,
I have a project that need to use a long range bluetooth communication with an Android smartphone or tablet
I use for test a tablet Lenovo Tab M8 TB8505F, NRF Connect...
Hi, before developing a BLE project, just got a general question about nRF connect on PC, does "nRF connect on PC" support Bluetooth 5 Advertising extension, if it is supported...
Hello. Developed with nrf52832 (S132 v7.0.1, SDK v16.0.0).
"pm_peer_delete" is used to delete the peer created during bonding. When I checked Flash when "PM_EVT_PEER_DELETE_SUCCEEDED...
Hi,
I have recently inherited a project from a former worker. The code intends to read data from a peripherial through TWI (the peripherial is a Si7053 digital temperature...
i used aplication twi_sensor form nRF5_SDK_12.3.0_d7731ad and i use s132.i conected mpu9060 every time get error on my terminl NRF_ERROR_BUSY.There is exemle of code main...
Hi,
I am working on a secure bootloader for a nRF52810 chip, and I am starting from the PCA10400e example in the SDK 16 and SD112 on SES (MacOS).
I successfully compiled...
Hi,
I am unable to get any programs using Zephyr to run on an nRF52840DK.
I have tried using the latest DAPlink (from GitHub) and JLink firmware (from Segger) as well...
When HFCLK was changed to "64 MHz crystal oscillator (HFXO)", the following code was implemented.
I am aware that "while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);" is waiting...
Hello all,
I would like to have some help regarding the usage of CoAP protocol. Is there any sample project that supports SDK 17.02 that I can start from?
I am using...
Hi DevZone,
Here's my setup:
Using NRF5 SDK 15.2.0, custom board based on NRF52840
Battery powered device with 3.6V battery.
Supply voltage stepped down to 1.8V...
Good day
Due to I am very new with NRF chips and I did not find direct answer on forum I require some clarification on that moment...
The task is to detect input pulse...
