Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
I would like to enable the APPROTECT readback protection.
What is the advised way to do this when using nrf connect/zephyr? The following line doesn't work (the 'at...
Hi everyone, I'm new to DevZone.
I am writing to ask for info for the first application with BLE.
I need to send data acquired by sensors, RAW mode, via the BLE application...
As far as I know "nRF Connect" DFU function just upgrade one by one,it's too low.
If there is no way to update in batches with DFU,who know a example that DFU function Host...
Hi Devzone:
I would like to shrink heap and stack size to save some RAM space.
I can see in the memory usage page of currently allocated heap and stack:
As you can...
Hello,
I have reserved an area in my flash mapping for settings (0x2000 length). I would like to update it (without application) with DFU / secured bootloader / nRF toolbox...
There is no 'low BLE power' example in the nRFConnect SDK for the nRF5340 - so I am just 'trying thinks' based on documentation I can find to come up with Application/BLE...
Hi.
I want to configure a scene when I create it on a node. So I need to use the Extension field sets, described in the ZCL 3.7.2.4.2.1. I see that the stack has a macro...
Hi Nordic Support Team,
My current setup is : Android Phone <--BLE--> nRF52840 <--LIBUARTE--> External STM32 MCU
I started the example with this folder in the link provided...
The following program will start the TIMER, read the timer value by pressing the button, and set the interrupt event. However, when the interrupt event is timed, the board...
Hai, I am using the sd_power_system_off() function for the deepest sleep mode, and my question what function used to wake up my system
I am using nrf52840 board with 17...
Hello, I need to upload the SEGGER script to FANSTEL EV-BT840 (832)-V4 via nRF52832, but there is something wrong with the connection. In my project, it is needed to use beaconing...
Referenece devzone example, : devzone.nordicsemi.com/.../mesh-mac-address
We should set the new MAC value via sd_ble_gap_addr_set before mesh_init( adv_start)
But flash...
Hi, I am looking to develop some code on NRF53. Looks like only Zephyr is supported. Even the most basic example includes some Zephyr files/libs. Reading the docs it sounds...
When I send hid data using below function. (length of data is just 5)
err_code = ble_hids_inp_rep_send ( p_hids ,
index ,
len ,
pattern ,
m_conn_handle );
...
