i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
I'm running OpenThread on a nrf52840-mdk from maker diary. I'm using the nRF SDK for thread and zigbee.
I would like to poll a sensor periodically. OpenThread does not offer...
hi support team,
i found that 52833 UART power is different from 832,
in SDK17.0.2,
832 is still 1.15 mA(with DMA), however 833 is about 0.437 mA(with DMA),
832 is...
Hello,
I want to use the BLE UART example on my PCA10040 development board, but I can´t transmit or receive any data from my PC to the smartphone with the nRF Connect app...
Hi all,
I have a question.
When I try send message coap, it can send as mesh network.
But when I send search gateway msg, connect msg from publish (subscribe) Node to...
My custom nRF9160 board does not communicate with nRF Connect Programmer.
"Unsupported device. The detected device could not be recognized as neither JLink device nor Nordic...
Hello everyone!
I have some issue with the comparator module on the nrf52820 chip.
We need to compare one of external analog signal the 1.8V internal reference source...
Hi,
I try to achieve high throughput via BLE connection between two nRF82540dk boards. I would like to maximize duty cycle of transmission in the connection interval. Unfortunately...
I am sending 240-byte data from peripheral to central through notification (without response) by using the ble_nus_data_send() function when the BLE_NUS_EVT_TX_RDY event comes...
Hi,
I received source code and compiled .hex file from Visual GDB from previsou developer.
I would like to continue development in Segger Embedded Studio.
I know the...
hi support team.
i want to use time from ntp server, and we have example in nrf/lib/data_time;
after devzone searching, i added below setting to prj.config
CONFIG_DATE_TIME...
Hi, I am trying to send data from one peripheral to a central unit and then relay the message to another peripheral unit over BLE. The peripheral already sends the data to...
Hi,
I'm trying to reinitialize my ANT stack, after update of parameters which is done by BT. To be exact, I'm setting the ANT ID of the ANT device that will send data to...
Hi,
I'm using a BMD-340 module evaluation kit (Rigado) I modified usbd example and I can transfer data in between host and device. But I have issues with usb speed and I...
Hi,
We are planning to use a NRF51 + NRF91 but we want to avoid maintain 2 custom firmwares. To avoid that, we want to use an LTE-M module with precompiled firmware.
I...
What i'm doing:
Running the peripheral_lbs code, and adding extra code to main loop (`for(;;)`).
What is happening:
Application runs fine, but breakpoints causes a fault...
