i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hi I am using the latest SDK for Mesh and also the latest nrf sdk. Downloaded and installed both last week. I have written an application that is derived from the light_switch...
Folks,
We are working on a custom design where the STM32L4 (external host MCU) talks to the nRF9160 over an UART connection to transmit sensor data. When the sensor data...
Hi,
I'm use nrf52840 with Light switch example of nRF5 SDK for Mesh v5.0.0 . Could I modify the packet of network layer ?
I want to add 2 bytes of UUID in the packet...
Hi, I want to add compression libraries like lz4 and audio compression to my zephyr projects. I am struggling to find good guides on how to add external/third party libraries...
Hi,
I have a nrf52810 board working as a peripheral, I want my board to connect to specific central application to protect it with malicious attack by other devices.
Please...
An error occurs when you run the following program(main.c).
[1;33m<wrn> bt_hci_core: opcode 0x2006 status 0x01 [1;31m<err> LOG_MODULE_NAME: Advertising start (err -5)
...
In the nrfConnect SDK I can see just one example for a I2C sensor - BH1749
I want to modify this for other I2C sensors.
However the README does not explain how to make...
I would like to calculate how much time my device does fast advertise and how much time it does slow advertising?
Is there a way to check this in python script?
Hi,
The SUPL Client library version 0.6.1 still links to the old BSD Libary, and will give a link failure, when building any application with SUPL Support
CMakeLists.txt...
Hello,
I am working to verify custom services on my device using nRF52 dev kit.
I am using HR collector example code as reference. I am able to read the custom service...
Hi,
I am trying to add the beacon Eddystone features to my DFU buttonless application.
After compiling the code, I wrote the softdevice, the bootloader and the application...
I am integrating a sensor on SPI 1 with cellular but device get stuck in CPU idle when first transaction of SPI is made?
I am using nrf9160dk_nrf9160ns as board configuration...
Starting with the dev kit, where I get correct behavior. First, I make sure the RESETREAS register is all zeros. I do this like so: NRF_POWER->RESETREAS = 0xFFFFFFFF; while...
Hello,
I am using nrf9160 and want to test the just simple SPI function. The code that I found from github( https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples...
Is there a way to set duty cycle before app_pwm_enable(&PWM1) call ?
Or some other simple way to switch on and off a passive buzzer signal without every time at off/on cycle...
