After ping through link local address ,i am not getting any Router solicitation messages,neighbor solicitation messages and neighbor advertisement messages while i am capturing...
Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
Hello,
The last ticket referencing this topic is 2 years old. I thought I would ask this question since we now have NCS.
Application is a Gateway that will support Zigbee...
I am trying to fun the LTE Sensor Gateway on the Thingy:91.
The boards are missing from zephyr so I copied nrf52840_pca20035 and nrf9160_pca20035 from ncs\nrf\boards\arm...
Dear all,
I'd first like to apologize if my questions seem dumb. I'm a student in mechanical engineering and only just started getting accustomed to microcontrollers and...
Hello,
I just installed SDK and Embedded studio.
And when I try to rebuild example, error occurs.
Below is my setup information.
- SDK: nRF5 SDK 16.0.0
- Example...
Hello support,
Currently i'm working with one application using NRF52832.
in which i have to fetch data from coming from PIC controller to NRF52832 over UART communication...
Hello, I owe a nRF9160 DK version 0.8.2. The ERRATA 0.7 document says that for this version the GPS antenna does not work well. I need to use GPS for extracting PPS signal...
Hi all, I've been recently working on PSM for my device, and I've not found any resources that answer my query or provide the knowledge I need. From my reading in this article...
Hello whenever I am calling sd_power_system_off(), it gives me the following error- implicit declaration of function 'sd_power_system_off'.
What shall be the optimum solution...
I use a 3.3V battery as VDD on an nRF52832 device.
Along the line this battery might do down from 3.3V to 1.8V. Will the Internal Reference Voltage be consistent at 1.8V...
Hi,
In apply_old_config.h ,here is the code:
for example:
If I set SYSTICK_ENABLED =0 in sdk_config,here will overwrite the macro define because #if defined(SYSTICK_ENABLED...
As per the datasheet of nrf52840 any peripheral like SPI/UART/... can be configured to any of the GPIOs so is the QSPI also.
But at Pin details QSPI pins are recommended...
Hello,
We are working on machine health monitoring system. For that we are using nRF52840 SOC as Central and nRF52833 SOC as end node. We had used single Central node and...
Hello.
I'm beginner on Nordic product and checking the examples with nRF5_SDK_17.0.0_9d13099 on nRF52833 DK Board.
I tested ble_app_uart and it works. Now checking ble_app_hrs...
Hello, I am
I'm a Beginner at developing NRF 51822 My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
Recently, I've been experiencing a lot of...
Hi,
I'm trying to find a way to power down and on again a RAM section, but I haven't had any luck finding.
In the SDK examples, there's a RAM retention example only, but...
