Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi All
I am a newbie with the nRF52 series SoC's and my end goal is to make a solar powered weather station.
I have a very crude nRF52832 dev board that I program with...
Hi, team.
There is a connection nfr52840 and esp32 (115200, 8, no parity, flow disable).
I'm using UARTE in interrupt mode (to send AT command and receive responses)....
Hi there, I am using the MDBT50Q-1MV2 Raytac module, with the nRF52840, and i have noticed that I have a very noisy VDD supply pin. Which definitely a problem because measures...
The qspi driver seems to make a number of assumptions about the protocol that don't fit the Winbond W25M02GW (and certain other) SPI flash chips.
Two major issues I've run...
I'm developing on an nRF52832 that has a serial connection with an iMX6 that is running a Python script with pySerial. For a while I had flow control disabled and would get...
hi i want to build a system with 500 device they send some data to controller wireless how can i do it with blu mesh ?
which chip should i select ? i prefer nrf52832
and...
nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730
nRF52840 Prewiew develpoment kit
I try to merge thread dfu client with simple coap server. there is error which i cant...
Hi! So I'm trying to use the throughput example with the nRF51422 board. infocenter.nordicsemi.com says that the SDK 12.3.0 throughput example will work with S130, which will...
Hi,
I want to interface sensor which has minimum requirement of UART supporting baudrate 921600 or SPI guaranteed maximum communication speed : 20 MHZ(Measured at 5cm...
Zigbee OTA upgrade example uses the Zigbee OTA cluster recommendations concerning the firmware file name (that is used for the version control and prevention of the downgrade...
Hi all,
We have custom board which has On Board Jlink support with nRF52832 using STM32 chip(STM32F072CBT6).
We are able to flash and debug using the On Board Jlink. ...
Hi there,
I was hoping someone could help me out. I recently got a hold of the nRF5 SDK for Mesh v2.0.1, and had a play around with the light switch example. I modified...
Hi,
I am trying to program my custom PCB using nRF 52 DK (I am using PCA10040 , nrf52382) as I have done countless times before. But suddenly embedded studio is giving me...
